Över 300 000 kunder - vi säger tack!

40 000+ produkter inom jakt och skytte

Lyft prestandan på ditt Remington gevär med WOLFFs RP trigger spring! 🎯 Enkel installation för bättre precision och kontroll.

WOLFF REMINGTON 700/721/722 TRIGGER SPRING - WOLFF REM. RP TRIGGER SPRING

969000173

Produktinformation

  • Modell: 700,721,722
  • Vapentyp: Remington
  • Leveransvikt: 0,005kg
  • Leveranshöjd: 10mm
  • Leveransbredd: 69mm
  • Leveranslängd: 142mm

Produkt detaljer

Tillverkas i USA
  • Specifikationer:
  • Make: Remington
  • Modell: 700, 721, 722
249 249 1 SEK
249 SEK 249 kr

Priser inkl. moms, exkl. frakt

Produktnr: 969000173

Tillv.nr.: 33240

Ge din Remington bultgevär en prestationshöjning med dessa lätta att installera fjädrar. Fjädern med reducerad kraft (RP) hjälper till att sänka den upplevda avtryckskraften för bättre, mer konsekvent noggrannhet.
Lagervara
1
2
3
4
5
6
7
8
9
10+
  • Specifikationer:
  • Make: Remington
  • Modell: 700, 721, 722

Beskrivning:

Visa original (engelska)
Minska Avtryckskraft
Ge din Remington bultgevär en prestationshöjning med dessa lätta att installera fjädrar. Fjädern med reducerad kraft (RP) hjälper till att sänka den upplevda avtryckskraften för bättre, mer konsekvent noggrannhet.

Produktinformation

  • Modell: 700,721,722
  • Vapentyp: Remington
  • Leveransvikt: 0,005kg
  • Leveranshöjd: 10mm
  • Leveransbredd: 69mm
  • Leveranslängd: 142mm

Produkt detaljer

Tillverkas i USA

Kundrecensioner

Kundbetyg (3)

2 / 5
Rekommenderar inte

Brownells USA Junk 2017-12-23

The factory spring allowed minimum of 4 lbs. This spring was shorter and stiffer than the factory spring. 6lbs was as low as you could go before the set screw no longer contacted the spring and the rifle became unsafe. Save time and money and go another route.

Rekommenderar

Brownells USA Helps a little 2015-07-26

Because Wolff's customer service is not knowledgeable about this product, I ended up going to another company's web site for installation instructions. This spring is NOT the one that goes behind the trigger. DO NOT try to remove the one that goes behind the trigger, and which is tensioned by the screw in the trigger. It goes in the front of the trigger housing assembly. You will need to remove the factory installed sealant to remove the screw that holds this spring in. Also, it is not as long as the one pictured here. It is about 1/3 that length. Trigger pull was reduced to about 3.5 # with this spring installed. That was on a gun that REMINGTON could not (or would not) reduce below 5 #. I sent two NEW rifles back to Remington because of heavy trigger pull. Despite the fact that the hang tag on the brand new guns states, "3 1/2 pounds out of the box" , Remington was unable to actually bring the guns into spec. The guns were returned to me with a heavy trigger pull, and a note explaining that they adjusted to 4.5# and 5.5 #, NOT 3.5. This spring helped, but keep in mind you will need to void the Remington warranty to bring it into Remington spec.

Visste du?

Tillverkarinformation

Ansvarig ekonomisk aktör enligt EU-förordningen

Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se

Oj! Något gick fel.

Vi stötte på ett fel när vi laddade innehållet. Vänligen uppdatera sidan för att fortsätta. Om problemet kvarstår, kontakta vår kundtjänst.

Tillbaka till toppen