Helt bearbetad från A2 verktygsstål, härdad till Rc 58 för hållbarhet och precision.
Minskar upplevd avtryckarkraft med upp till 50 procent, vilket förbättrar skjutprecisionen.
Installation utan modifikationer, passar både .22LR och .22WMR avtryckarbågar.
Produktinformation
Modell:597
Vapentyp:Remington
Leveransvikt:0,014kg
Leveranshöjd:8mm
Leveransbredd:71mm
Leveranslängd:86mm
UPC:810162011321
Produkt detaljer
Tillverkas i USA
USA: s exportklassificering: 0A501.c
Specifikationer:
Make: Remington
Modell: 597
9999991SEK
999SEK999 kr
Priser inkl. moms, exkl. frakt
Produktnr: 930000019
Tillv.nr.: VCRTH
810162011321 Helt maskinbearbetad från A2 verktygsstål med hammarnotchen individuellt, ytbearbetad för att säkerställa en exakt vinkel för engagemang. Minskar den upplevda avtrycksvikten med upp till 50 procent. Enkel installation; använd i en oförändrad, fabriksavtrycksskydd. Passar både .22LR och .22WMR.
Lagervara
Levernastid ca. 14-21 dagar. 6 st. i centrallagret.
Levernastid ca. 14-21 dagar. 6 st. i centrallagret.
Fully machined from A2 tool steel with the hammer notch individually, surface ground to ensure an exact angle of engagement. Reduces felt trigger pull by up to 50 percent. Drop-in installation; use in an unaltered, factory triggerguard. Fits both the .22LR and .22WMR.
Minskar Avtrycksvikt För Att Förbättra Noggrannheten
Helt maskinbearbetad från A2 verktygsstål med hammarnotchen individuellt, ytbearbetad för att säkerställa en exakt vinkel för engagemang. Minskar den upplevda avtrycksvikten med upp till 50 procent. Enkel installation; använd i en oförändrad, fabriksavtrycksskydd. Passar både .22LR och .22WMR.
Top takeaways
Helt bearbetad från A2 verktygsstål, härdad till Rc 58 för hållbarhet och precision.
Minskar upplevd avtryckarkraft med upp till 50 procent, vilket förbättrar skjutprecisionen.
Installation utan modifikationer, passar både .22LR och .22WMR avtryckarbågar.
Produktinformation
Modell:597
Vapentyp:Remington
Leveransvikt:0,014kg
Leveranshöjd:8mm
Leveransbredd:71mm
Leveranslängd:86mm
UPC:810162011321
Produkt detaljer
Tillverkas i USA
USA: s exportklassificering: 0A501.c
Kundrecensioner
Kundbetyg (8)
5 / 5
Rekommenderar varmt
YouTube Video helps 2016-05-13
My 597 has a great barrel, but a lousy trigger. Getting the most out of your gun comes right down to the trigger. Why do you think benchrest shooters use 4 - 6 Oz. triggers. So I ordered this item with my fingers crossed. Got it promptly and installed it in 45 minutes. Use Youtube video (9min ) and it is very straight forward. End result Trigger pull 3 1/4 - 3 1/2 Lbs.
Now to get to the range.
Rekommenderar varmt
great product 2014-09-02
This hammer combined with a Brownell's extractor made an otherwise misfiring and jamming gun shoot flawlessly. I was able to shoot four different types of ammo totaling about 400 rounds without any FTE or FTF. This gun out of the box did not function properly. Now it shoots great and is extremely accurate. A must upgrade for any Remington 597 owner!
Rekommenderar varmt
Effective Solution 2013-12-02
This was the perfect solution for the VERY heavy trigger on my daughter's 597. Easy to install; but be patient with the pin for the hammer.
Now the pull is crisp and light, with no creep. Trigger pull was reduced by more than 50%
This product was very cost effective compared to some of the other solutions out there.
High Quality Product!
Rekommenderar varmt
Need to have in your Remington 597 2013-11-13
I'm very pleased about this product, really surpised about how it works overrided my spectatives, my Rem597 is in a new level of trigger and shooting control. Very fast shipping and a real proffesional package. My first but not my last buy with brownells. Thanks a lot.
Rekommenderar varmt
Great Prodct!! 2012-01-17
Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.
Rekommenderar varmt
BUY IT 2011-12-25
Easy to install. Reduces triger pull. Smoother trigger. Buy it. You will love it.
Rekommenderar varmt
Money well spent!! 2011-06-03
If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!
Rekommenderar varmt
Worth the Effort 2010-07-22
Just finished installing the hammer. Initial trigger pull approx. 4 1/2 lbs. according to spring gauge. After installation: 2 lbs. Minimal creep. Took about 15-20 minutes. Remove trigger housing from receiver by removing the one retaining pin at rear of trigger housing(if bolt is closed, may have to pull back slightly to get housing to pop free). Place housing in padded vice at a slight angle to avoid crushing mag release button. Housing is composite so easy does it. Tap out hammer pin with punch but just enough to release hammer-don't drive out all the way. Don't remove punch but leave in pin hole to keep spring and plastic bushing in place(there are two plastic bushings inside of spring on both sides of hammer). Remove old hammer and slide in new one, align pin holes and reinstall hammer pin. You may find that you cannot get the hammer to go to the cocked position. If this is so, you have to push the trigger fully forward and the hammer should stay in the cocked position now. Install housing back into receiver and replace the one retaining pin. Install upper assembly back into stock and your done. With gun empty, check to make sure rifle fires after bolt is cycled. Mine functioned flawlessly. If you completed the job without ending up with a bunch of extra parts, you should be very pleased with the results.
Uppgradera din Remington 597 med Volquartsen Target Hammer! 🎯 Minska avtryckarkraften med upp till 50% för en bättre skytteupplevelse.
Destination Control Statement: Dessa poster styrs av USA: s regering och godkänns endast för export till det land där den slutliga destinationen används av den slutliga mottagaren eller slutanvändaren som identifierats här. De får inte vidareförsäljas, överföras eller på annat sätt kasseras till något annat land eller någon annan än den godkända slutliga mottagaren eller slutanvändaren, antingen i sin ursprungliga form eller efter att ha monterats i andra föremål utan att först få godkännande från den amerikanska regeringen eller som annars är tillåten enligt amerikansk lag och förordningar.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Destination Control Statement: Dessa poster styrs av USA: s regering och godkänns endast för export till det land där den slutliga destinationen används av den slutliga mottagaren eller slutanvändaren som identifierats här. De får inte vidareförsäljas, överföras eller på annat sätt kasseras till något annat land eller någon annan än den godkända slutliga mottagaren eller slutanvändaren, antingen i sin ursprungliga form eller efter att ha monterats i andra föremål utan att först få godkännande från den amerikanska regeringen eller som annars är tillåten enligt amerikansk lag och förordningar.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Lätta aluminiumbaser som passar både moderna och äldre gevär, samt hagelgevär och handeldvapen för långdistansskytte.
Säljs styckvis eller i par, med specifika modeller markerade med * eller **.
Kompatibla med Top Mount och See-Thru Mount Rings, tillverkade av WEAVER med polerad blå finish, Matt (M) eller Silver (S).
ELD-X® kulan erbjuder högsta klassens ballistiska koefficienter och kontrollerad expansion vid alla praktiska jaktdistanser tack vare Heat Shield®-spetsen.
Den strömlinjeformade designen med sekant ogiv och båtstjärtdesign kombinerat med AMP® kulmantlar och Heat Shield®-spets ger överlägsen aerodynamisk effektivitet.
Vid konventionella avstånd (0-400 yards) expanderar kulan kontinuerligt och behåller 50-60% vikt, medan vid långa avstånd (400+ yards) initierar Heat Shield®-spetsen expansion för djup penetration och stora sårkanaler.
Lee Universal Decapping die är tillverkad av stål och möjliggör avkapsling av hylsor utan behov av smörjmedel eller rengöring.
Verktyget är garanterat okrossbart och tar enkelt bort inpressade tändhattar.
Passar hylsor upp till .550” men rekommenderas inte för kalibrar mellan .17-.20.