Varukorgen är tom.

Varukorg

Hjälp och kontakt

Fri frakt på beställningar över 2.999 kr

100 dagars returrätt

Nyhetsbrev

REA

Över 300 000 kunder - vi säger tack!

4,93/5 "Mycket bra" (1400+ recensioner)

40 000+ produkter inom jakt och skytte

VOLQUARTSEN
REMINGTON 597 TARGET HAMMER

810162011321 930000019

Reduces Pull Weight To Improve Accuracy

Fully machined from A2 tool steel with the hammer notch individually, surface ground to ensure an exact angle of engagement. Reduces felt trigger pull by up to 50 percent. Drop-in installation; use in an unaltered, factory triggerguard. Fits both the .22LR and .22WMR.

SPECS: A2 tool steel, in the white. Hardened to Rc 58.

Mer...

Reducerar Avtryckarvikt För Förbättrad Precision

Helt bearbetad från A2 verktygsstål med hammarnacken individuellt, ytjämnad för att säkerställa en exakt vinkel för ingripande. Minskar upplevd avtryckarkraft med upp till 50 procent. Installation utan modifikationer; används i en oförändrad, fabrikstillverkad avtryckarbåge. Passar både .22LR och .22WMR.

SPECS: A2 verktygsstål, i grundutförande. Härdat till Rc 58.

Mer...

Kundernas betyg påVOLQUARTSEN TARGET HAMMER

Antal betyg: 8
Från brownells.com: 8
Medelbetyg: 5

Worth the Effort (2010-07-22)

Just finished installing the hammer. Initial trigger pull approx. 4 1/2 lbs. according to spring gauge. After installation: 2 lbs. Minimal creep. Took about 15-20 minutes. Remove trigger housing from receiver by removing the one retaining pin at rear of trigger housing(if bolt is closed, may have to pull back slightly to get housing to pop free). Place housing in padded vice at a slight angle to avoid crushing mag release button. Housing is composite so easy does it. Tap out hammer pin with punch but just enough to release hammer-don't drive out all the way. Don't remove punch but leave in pin hole to keep spring and plastic bushing in place(there are two plastic bushings inside of spring on both sides of hammer). Remove old hammer and slide in new one, align pin holes and reinstall hammer pin. You may find that you cannot get the hammer to go to the cocked position. If this is so, you have to push the trigger fully forward and the hammer should stay in the cocked position now. Install housing back into receiver and replace the one retaining pin. Install upper assembly back into stock and your done. With gun empty, check to make sure rifle fires after bolt is cycled. Mine functioned flawlessly. If you completed the job without ending up with a bunch of extra parts, you should be very pleased with the results.

Money well spent!! (2011-06-03)

If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!

BUY IT (2011-12-25)

Easy to install.
Reduces triger pull.
Smoother trigger.
Buy it. You will love it.

Great Prodct!! (2012-01-17)

Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.

Need to have in your Remington 597 (2013-11-13)

I'm very pleased about this product, really surpised about how it works overrided my spectatives, my Rem597 is in a new level of trigger and shooting control. Very fast shipping and a real proffesional package. My first but not my last buy with brownells. Thanks a lot.

Effective Solution (2013-12-02)

This was the perfect solution for the VERY heavy trigger on my daughter's 597. Easy to install; but be patient with the pin for the hammer.

Now the pull is crisp and light, with no creep. Trigger pull was reduced by more than 50%

This product was very cost effective compared to some of the other solutions out there.

High Quality Product!

great product (2014-09-02)

This hammer combined with a Brownell's extractor made an otherwise misfiring and jamming gun shoot flawlessly. I was able to shoot four different types of ammo totaling about 400 rounds without any FTE or FTF. This gun out of the box did not function properly. Now it shoots great and is extremely accurate. A must upgrade for any Remington 597 owner!

YouTube Video helps (2016-05-13)

My 597 has a great barrel, but a lousy trigger. Getting the most out of your gun comes right down to the trigger. Why do you think benchrest shooters use 4 - 6 Oz. triggers. So I ordered this item with my fingers crossed. Got it promptly and installed it in 45 minutes. Use Youtube video (9min ) and it is very straight forward. End result Trigger pull 3 1/4 - 3 1/2 Lbs.

Now to get to the range.

Läs 8 fler betyg på brownells.com

999 999 1 SEK

Produktnr: 930000019
VOLQUARTSEN TARGET HAMMER
Tillverkarens produktnummer: VCRTH 810162011321 Helt bearbetad från A2 verktygsstål med hammarnacken individuellt, ytjämnad för att säkerställa en exakt vinkel för ingripande. Minskar upplevd avtryckarkraft med upp till 50 procent. Installation utan modifikationer; används i en oförändrad, fabrikstillverkad avtryckarbåge. Passar både .22LR och .22WMR.

999 SEK 5 999,00 kr *

Levernastid ca. 14-21 dagar.
5 st. i centrallagret.

Funktioner: Make: Remington Modell: 597

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Top takeaways

Helt bearbetad från A2 verktygsstål, härdad till Rc 58 för hållbarhet och precision.
Minskar upplevd avtryckarkraft med upp till 50 procent, vilket förbättrar skjutprecisionen.
Installation utan modifikationer, passar både .22LR och .22WMR avtryckarbågar.

Produktinformation

Make: Remington Modell: 597 Leveransvikt: 0,014kg Leveranshöjd: 8mm Leveransbredd: 71mm Leveranslängd: 86mm UPC : 810162011321

Produkt detaljer

Tillverkas i USA
USA: s exportklassificering: 0A501.c

Ansvarig ekonomisk aktör enligt EU-förordningen

Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se

Uppgradera din Remington 597 med Volquartsen Target Hammer! 🎯 Minska avtryckarkraften med upp till 50% för en bättre skytteupplevelse.

Reduces Pull Weight To Improve Accuracy

SPECS: A2 tool steel, in the white. Hardened to Rc 58.

Mer...

Reducerar Avtryckarvikt För Förbättrad Precision

SPECS: A2 verktygsstål, i grundutförande. Härdat till Rc 58.

Mer...

Kundernas betyg påVOLQUARTSEN TARGET HAMMER

Antal betyg: 8
Från brownells.com: 8
Medelbetyg: 5

Worth the Effort (2010-07-22)

Money well spent!! (2011-06-03)

If you buy one part for your 597, make it this! Very easy installation and a dramatic difference in trigger pull. I still just can't believe how smooth and nice it is. Just buy it!!

BUY IT (2011-12-25)

Easy to install.
Reduces triger pull.
Smoother trigger.
Buy it. You will love it.

Great Prodct!! (2012-01-17)

Slid this puppy right into my HB 597 after getting really good on-line videos do demonstrate (at Rimfirecentral.com) or elsewhere. It does exactly as claimed, makes trigger light and crisp.

Need to have in your Remington 597 (2013-11-13)