BROWNELLS
AR-15/M16 EXTRACTOR BUFFER

078000071

Stronger Base For Eliminating Extractor Bounce

Tough, dense rubber insert replaces factory buffer inside the extractor spring to prevent extractor bounce that can occur in rapid-fire conditions. Insert keeps the extractor from losing contact with casings and reducing faulty ejection of the spent casing. Sold in 10-paks.

SPECS: Rubber, black. .15" (3.8mm) long, .11" (2.8mm) diameter 10-paks.

Mer...

Starkare bas för att eliminera extraktorstuds

Tålig, tät gummipackning ersätter fabriksbufferten inuti extraktorfjädern för att förhindra extraktorstuds som kan förekomma vid snabb eldgivning. Insatsen håller extraktorn från att tappa kontakten med hylsorna och minskar risken för felaktig utkastning av det förbrukade hylsan. Säljs i 10-pack.

SPECS: Gummi, svart. .15" (3.8mm) lång, .11" (2.8mm) diameter 10-pack.

Mer...

Kundernas betyg påBROWNELLS EXTRACTOR BUFFERS, 10-PAK

Antal betyg: 2
Från brownells.com: 2
Medelbetyg: 5

Not all older extractors have these. (2010-04-25)

Extractor bounce is an easily overlooked symtom of failure to extract. Uncle Sam uses a blue buffer, but so far, these seem to work just as well. They are easy to install, don't fall out, and they actually work pretty well for plugging the listening holes of a friends telephone if you're into such tomfoolery. One of my older AR bolts did not have a buffer and I started noticing the occasional FTE with max trim length reloads. This cured it- and did not need the donut ring.

If you're not running one, YOU'RE WRONG (2014-07-08)

This is an extractor buffer. It fits inside of the base of the extractor spring (the wider part of the spring that snaps into the cup on the extractor). This is the black version, an upgraded form of the original blue version. The blue version was designed to be used with the M16A2 rifle and the higher pressure M855 62gr ammunition (which was causing extraction problems). The blue buffer, however, did not supply enough support to the extractor spring for the shorter M4 gas system (carbine length; 7" gas tube). The carbine system exhibits faster (and some would say premature) extraction due to the shorter gas system dwell time and also higher gas port pressures. This meant multiple failures to extract in combat. The black insert was developed for the carbine system but is also compatible with the rifle length gas system. If you don't know what extractor spring you are running in your gun and you don't own a Colt or BCM, then use this as an opportunity to purchase a Wolff XP or Colt Copper-washed extractor spring and use them with these buffers (both available here on Brownells).

Put simply, they are VERY cheap insurance and there is NO REASON to not use one in any and every AR15. Use these on every gas system length (pistol, carbine, mid-length, intermediate, and rifle length).

Läs 2 fler betyg på brownells.com

349 349 1 SEK

Produktnr: 078000071
BROWNELLS EXTRACTOR BUFFERS, 10-PAK
Tillverkarens produktnummer: NONE Tålig, tät gummipackning ersätter fabriksbufferten inuti extraktorfjädern för att förhindra extraktorstuds som kan förekomma vid snabb eldgivning. Insatsen håller extraktorn från att tappa kontakten med hylsorna och minskar risken för felaktig utkastning av det förbrukade hylsan. Säljs i 10-pack.

349 SEK 0 349,00 kr *

Ej tillgänglig.

Funktioner: Make: AR-15

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Top takeaways

Tålig gummipackning ersätter fabriksbufferten inuti extraktorfjädern för att förhindra extraktorstuds vid snabb eldgivning.
Förhindrar att extraktorn tappar kontakten med hylsorna och minskar risken för felaktig utkastning av förbrukade hylsor.
Säljs i 10-pack, tillverkad av Brownells för AR-15, specifikationer: Gummi, svart, .15" (3.8mm) lång, .11" (2.8mm) diameter.