Över 300 000 kunder - vi säger tack!

40 000+ produkter inom jakt och skytte

Upptäck WINCHESTER 94 Pre-'64 Stock Set 🪵 i klassisk valnöt, perfekt för anpassning. Kvalitetsträ redo för slipning och ytbehandling.

WOOD PLUS WINCHESTER 94 PRE-'64 STOCK SET (UNFINISHED) - WOOD PLUS WINCHESTER 94 PRE-'64 STOCK SET

984110094

Produktinformation

  • Färg: Unfinished
  • Material: Wood
  • Modell: 94
  • Stil: Fixed
  • Vapentyp: Winchester
  • Leveransvikt: 0,794kg
  • Leveranshöjd: 69mm
  • Leveransbredd: 137mm
  • Leveranslängd: 457mm

Produkt detaljer

Tillverkas i USA
USA: s exportklassificering: 0A501.y.1
  • Specifikationer:
  • Färg: Unfinished
  • Make: Winchester
  • Material: Wood
  • Modell: 94
  • Stil: Fixed
1849 1849 1 SEK
1849 SEK 1 849 kr

Priser inkl. moms, exkl. frakt

Produktnr: 984110094

Tillv.nr.: NONE

Klassisk valnöt ger en nära matchning till originalfabriksstockar. Kvalitetsved, har ett rakt ådringsmönster. 95% förbearbetad för enkel anpassning till din åtgärd. Klar för slutlig slipning, färgning och ytbehandling.
Lagervara
1
2
3
4
5
6
7
8
9
10+
  • Specifikationer:
  • Färg: Unfinished
  • Make: Winchester
  • Material: Wood
  • Modell: 94
  • Stil: Fixed

Beskrivning:

Visa original (engelska)
Äkta Valnöt För Ersättning & Restaurering
Klassisk valnöt ger en nära matchning till originalfabriksstockar. Kvalitetsved, har ett rakt ådringsmönster. 95% förbearbetad för enkel anpassning till din åtgärd. Klar för slutlig slipning, färgning och ytbehandling.

SPECS: Valnöt, rak ådring, ingen figur. Accepterar original hårdvara. Win. 94 Pre '64 passar karbinmodeller.

Produktinformation

  • Färg: Unfinished
  • Material: Wood
  • Modell: 94
  • Stil: Fixed
  • Vapentyp: Winchester
  • Leveransvikt: 0,794kg
  • Leveranshöjd: 69mm
  • Leveransbredd: 137mm
  • Leveranslängd: 457mm

Produkt detaljer

Tillverkas i USA
USA: s exportklassificering: 0A501.y.1

Kundrecensioner

Kundbetyg (1)

5 / 5
Rekommenderar varmt

Brownells USA Pre 64 model 94 Winchester stock set 2015-12-11

I purchased one of these sets from another supplier for a much higher price. It was for one of two restorations I am working on. It is not a project for impatient people. It requires a good bit of fitting and attention to detail. That being said, with some patience and thinking before acting, it will come out as good, or better than the factory furniture. I removed the old furniture and started setting the individual pieces in place for test fitting. I used a fine scribe to mark the edges of the metal. After removing the marked wood, I used an orbital sander with 80 grit paper to remove the major portion of the excess on the forearm. I then used the same orbital sander with 100 grit until the lines were barely visible and finally 150 grit until the stock was smooth. I used fine metal files to trim the projections for the receiver recesses. After a number of fittings, the forearm had a better fit and appearance than the original. I did the same procedure for the stock. The only difference was that I placed the buttplate in position and screwed it in prior to marking the stock. I hand sanded the pieces with 220 grit after the last test fit The best advice I can give is be patient, take your time and think before you act. I will be purchasing my second one from Brownells.

Visste du?

Tillverkarinformation

Ansvarig ekonomisk aktör enligt EU-förordningen

Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se

Oj! Något gick fel.

Vi stötte på ett fel när vi laddade innehållet. Vänligen uppdatera sidan för att fortsätta. Om problemet kvarstår, kontakta vår kundtjänst.

Tillbaka till toppen