WOLFF TRIGGER GROUP COMPETITION PAK for GLOCK®

I installed this competition spring pack with a Ghost 3.5 Ultimate trigger connector---I ended up using only the trigger reset and safety block springs. With the 3.5 connector and these 2 springs my trigger is a nice 4-4.25 lbs.

With the Wolff firing pin spring, the trigger ended up below 3.5 and the reset was very mushy. This is a carry gun, and as warned in the product description, these springs will give you a scary light trigger pull so I got exactly what I paid for. I would give full stars except for the mushy reset.

Makes trigger pull around 3 to 3.5lbs or so. I only put 2 of the springs in. I leave the s spring out. When the s spring is in it is dangerously light, probably around 1.5lbs. Great product without spending lots of money on triggers that you might not like. Only bad thing is you still have the long reset, it does not take care of that. I recommend this product. I Have it in all my glocks and a similar product in my XD.

I have been using these for about 12 years in various glocks I use in competitions. The springs are excellent and I think last longer than the stock springs do. Lightens up the pull weight nicely to help with accuracy.

This kit is the single greatest improvement you can make to a Glock trigger. I have used these kits FOR COMPETITION for 8 years in G-17, 19, 21 and 34, with and without the "3.5 lb." connector. I installed just the striker spring in a stock G-19 yesterday and made the gun 100% easier to shoot accurately.

As with anything, you can over do it, but I have never found this kit or any part of it to be unsafe or have any undesired effects. Any gun can fire if something enters the trigger guard while holstering. The only thing that resets the "trigger safety" is gravity or inertia and the notion that this kit contributes to an unsafe condition is silly. It is harder to pull the trigger than to depress the "trigger safety."

By installing all three springs trigger pull becomes much lighter. Have used the kit with G17 Gen.4.

But as others have mentioned too the trigger safety will not re-engage if trigger is pulled slightly and released again.

I use only safety plunger spring form this set. One of the remainig two could also be used. I also have the minus connector installed.

Neat kit to improve your G's pull but keep the risks in mind!

I have installed around 2 dozen of these kits and as stated above if all three are installed with a reduced power connector it does create a possible hazard. I depending on what the desired trigger pull weight is istall the safety plunger spring and the trigger spring or the safety plunger and the reduced power firing pin srping. I never install all three. I have had nothing but good results from these combinations and have never had a reported failure to fire with the reduced power spring.

With these springs and a 3.5 lb. connector, my Glock 21 has a silky, smooth action.

But as said before, this kit causes a tremendous safety concern. Partially depressing the trigger and releasing it does not allow the trigger to fully return, and the trigger safety will not re-engage. The extra-power trigger spring is the main culprit.

Unsatisfied with this condition, I reinstalled the factory trigger spring, and the trigger safety now works as it should.

And at some point, I will reinstall the factory striker spring since my Glock is used for HD and I don't want to risk a failure to fire from the reduced power spring.

I still think it was worth trying and I'm anxious to test it at the range.

Love the Glock, not thrilled with the trigger pull.
Dropped in a Ghost 3.5 trigger connector and ONLY the striker spring from this kit. Very nice trigger now. Not as nice as a tuned 1911, but compared to stock it is great. This way, everything else is still stock.

I've used Wolff springs in several guns, and they provide a couple of much needed tweaks to the factory Glock trigger. A light takeup and much more noticeable, firmer second stage before the striker falls. Coupled with some polishing in the right places (or an aftermarket connector) this spring kit gives great results.

While I have never had any issues with trigger return or firing pin safety engagement, I would still caution buyers to test the pistol extensively with and without the reduced power safety plunger spring, just in case.

This product was easy to install and definitely reduced the trigger pull. Unfortunately, it also made the trigger safety unreliable on my gun.

Reseting the trigger by cycling the action would reset the trigger and trigger safety normally. If you partially depressed the trigger -- without releasing the striker -- and then let off the trigger, the trigger safety would not re-engage.

In my opinion, this creates an unsafe pistol because it makes 1 of the 3 safeties unreliable. I will not even use this in my competition only guns for fear of an accidental discharge while holstering.

The springs work as advertised to reduce trigger pull. In fact, I would describe the results as beautiful for a Glock! You do, however, need to heed their competition only warning!

After installing, the springs would reset the trigger when dry fired + action cycled. The trigger safety, however, would not reset on its own if you initiated trigger pull and then let off.

This could lead to an accidental discharge if you were to inadvertantly disengage the trigger safety then catch the trigger on somthing. E.g., on your shirt while holstering.

Therefore, I'm only giving this 2 stars for function because, at least in my guns, it created an unsafe firearm and I value safety more than anything else.

easy to install and made my trigger much lighter. love this kit