Upptäck S&W Revolver Extra Length Firing Pin för pålitlig tändning och förbättrad träff. ✨ Passar J, K, L och N-ramar.
CYLINDER & SLIDES&W REVOLVER EXTRA LENGTH FIRING PIN - CYLINDER & SLIDE EXTRA LONG S&W FIRING PIN
000000001885206000010
Produktinformation
Kaliber:38/357 Caliber (.357-.359),41 Caliber (.410-.412),45 Caliber (.451-.454),9 mm (.355-.356),40/10 mm (.400-.401),32 Caliber (.312-.313)
Modell:J Frame,K Frame,L Frame,N Frame
Vapentyp:Smith & Wesson
Leveransvikt:0,009kg
Leveransbredd:83mm
Leveranslängd:146mm
UPC:000000001885
Produkt detaljer
Tillverkas i USA
USA: s exportklassificering: 0A501.x
Specifikationer:
Kaliber: 38/357 Caliber (.357-.359), 41 Caliber (.410-.412), 45 Caliber (.451-.454), 9 mm (.355-.356), 40/10 mm (.400-.401), 32 Caliber (.312-.313)
Make: Smith & Wesson
Modell: J Frame, K Frame, L Frame, N Frame
4594591SEK
459SEK459 kr
Priser inkl. moms, exkl. frakt
Produktnr: 206000010
Tillv.nr.: CS0188
000000001885 015", extra-lång pin låter dig använda den lättaste möjliga huvudfjädervikten och ändå uppnå konsekvent och tillförlitlig tändning. Förbättrar tändstiftets träff på nya modellrevolvrar med rammonterat tändstift. Drop-in passform.
Lagervara
Levernastid ca. 14-21 dagar. 8 st. i centrallagret.
Levernastid ca. 14-21 dagar. 8 st. i centrallagret.
015", extra-length pin lets you use the lightest possible mainspring weight and still achieve consistent and reliable ignition. Improves firing pin strike on new model revolvers with the frame mounted firing pin. Drop-in fit.
Ger Tillförlitlig & Konsekvent Tändning
015", extra-lång pin låter dig använda den lättaste möjliga huvudfjädervikten och ändå uppnå konsekvent och tillförlitlig tändning. Förbättrar tändstiftets träff på nya modellrevolvrar med rammonterat tändstift. Drop-in passform.
Produktinformation
Kaliber:38/357 Caliber (.357-.359),41 Caliber (.410-.412),45 Caliber (.451-.454),9 mm (.355-.356),40/10 mm (.400-.401),32 Caliber (.312-.313)
Modell:J Frame,K Frame,L Frame,N Frame
Vapentyp:Smith & Wesson
Leveransvikt:0,009kg
Leveransbredd:83mm
Leveranslängd:146mm
UPC:000000001885
Produkt detaljer
Tillverkas i USA
USA: s exportklassificering: 0A501.x
Kundrecensioner
Kundbetyg (10)
3,3 / 5
Rekommenderar i viss mån
Doesn't last long 2018-01-29
Works well. Ran them in my 4 competition S&W's. Had one break in my Life frame, fortunately not during a match. Read that this is a common problem. Pulled them all out and went with Apex.
I would not recommend, because there is a better product.
Rekommenderar inte
Poor Product 2017-01-07
Does not work even with full power mainspring had misfires
Rekommenderar med reservationer
It worked fine --- for AWHILE. 2014-07-02
I teach tons of CCW classes and I have my students shoot a Sig Mosquito and a S&W 617. The 617 started having misfires after about 20K rounds and it looked like the firing pin was not hitting the 22 rims very hard so I bought this long pin. The misfiring was cured but the firing pin broke after about 5000 rounds. I installed another one. We'll see what happens.
Rekommenderar varmt
Flawless Ignition with 202 Spring Kit... 2014-03-21
I recently upgraded a stock 629-6 using a Brownells 202 Spring Kit(standard rate Power Rib Main Spring with 13, 14, and 15 lbs Trigger Rebound Springs). I replaced the stock Main Spring & Trigger Rebound Spring with the kit's standard rate Power Rib Main Spring and the 15lbs Trigger Rebound Spring. This resulted in greatly improved reasonably light & smooth SA/DA pulls but as is often the case with lighter than stock aftermarket spring upgrades, I could not get 100% reliable ignition with a variety of primer makes & types. As component availability is now so hit & miss, for me it is absolutely crucial that this handgun be able to shoot loads using whatever type of primers are available with 100% reliability. Replacing the stock firing pin with the C&S Extra Long S&W Firing Pin from Brownells instantly solved the issue. After swapping out the stock firing pin I achieved 100% reliable ignition with loads using the several makes & types of primers I have stocked up on as they became available, including the Large Pistol Magnum primer that is so notoriously hard to ignite. As others have pointed out the pin itself is not longer but the travel cut is wider which allows the pin to travel forward a shade more. That little bit more inertia combined with the face of the pin being more rounded & wider than a stock S&W pin yielded flawless ignition across the board. Fit was perfect & finish excellent resulting in easy drop-in installation. I could not be happier with this firing pin and highly recommend that if you are going to install an aftermarket spring kit in a S&W revolver, you swap out the stock firing pin for this one at the same time. It will save you a ton of frustration. Once more a great product from Brownells. Thanks!
Rekommenderar varmt
fixed problem 2014-01-15
had problem with misfire, my revolver has to big of gap between cylinder and frame (like somebody tried to make it work with moon clips) dropped firing pin in, cleared problem right up
Rekommenderar varmt
A must for Federal Primers & Trigger Job 2014-01-04
I have these in all my S&W Revolvers.
The extra length is in the travel, not the length of the pin. Look at the groove in the body (thick part) of the pin. That's where the extra travel is provided.
Be careful not to loose and be sure to re-install the spring that already exist in your revolver.
A good trigger job with a 6# double action pull will require this and Federal primers for reliable ignition.
Rekommenderar varmt
Good Trigger Job Accessory 2012-10-27
I put this in a S&W Governor, The OAL is about the same as the factory FP but, the actual FP Protrusion was .011 greater than the factory FP, and that is what matters. I used a Wilson Combat Spring Kit and this thing to do the job and it turned out nice. FP Protrusion is measured form the breech/bolt face to the tip of the FP with a FP Protrusion Gauge and a Micrometer, not by measuring the OAL.
Rekommenderar inte
Standard Length 2012-05-11
Same length as stock K-frame firing pin.
Rekommenderar inte
Came up short. 2012-04-28
0.018" shorter than the stock FP in my N frame.
Rekommenderar varmt
Good Product 2010-11-29
I installed this on an Airweight J-Frame S&W 637 to prevent light strikes. I was initially concerned that it might cause punctured primers due to the added length. However, upon testing it with several different factory cartridges (standard and +P), I found no sign of excessive primer damage. Actually, the design of this product is quite smart... the pin may be a bit longer, but the tip is more blunt than the pointed stock pin. The added surface area and extra length make a nice, smooth, wide dent that ignites primers with gusto. Just make sure you test it thoroughly as results might vary from one gun to the next.
Upptäck S&W Revolver Extra Length Firing Pin för pålitlig tändning och förbättrad träff. ✨ Passar J, K, L och N-ramar.
Destination Control Statement: Dessa poster styrs av USA: s regering och godkänns endast för export till det land där den slutliga destinationen används av den slutliga mottagaren eller slutanvändaren som identifierats här. De får inte vidareförsäljas, överföras eller på annat sätt kasseras till något annat land eller någon annan än den godkända slutliga mottagaren eller slutanvändaren, antingen i sin ursprungliga form eller efter att ha monterats i andra föremål utan att först få godkännande från den amerikanska regeringen eller som annars är tillåten enligt amerikansk lag och förordningar.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Destination Control Statement: Dessa poster styrs av USA: s regering och godkänns endast för export till det land där den slutliga destinationen används av den slutliga mottagaren eller slutanvändaren som identifierats här. De får inte vidareförsäljas, överföras eller på annat sätt kasseras till något annat land eller någon annan än den godkända slutliga mottagaren eller slutanvändaren, antingen i sin ursprungliga form eller efter att ha monterats i andra föremål utan att först få godkännande från den amerikanska regeringen eller som annars är tillåten enligt amerikansk lag och förordningar.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Enstyckeskonstruktion som ger ett stabilt grepp utan skift eller vackel, vilket förbättrar koncentration och precision.
Ergonomisk design som exakt positionerar både höger- och vänsterhand och hjälper till att absorbera rekyl.
Gummi- och nylongrepp med stippelad yta förhindrar handglidning utan att slita på kläder vid bärande i hölster.