Increased pressure stabilizes the follower and improves feeding, especially on high-capacity magazines. SIG P220 provides 10% more power in your older .45 ACP Sig P220 and is the factory standard spring in newer P220s with a green recoil spring. Also fits the Browning BDA .45 ACP. Separate models available for magazines with a metal floorplate (MF) or a plastic floorplate (PF). Will not fit 8-round magazines made by Mec-Gar.
SPECS: Will not fit Meg-Gar Sig 220 magazines and 70873 fits Metal Floor plate Sig 220 and BDA magazines only, 79383 fits Plastic Floor plate Sig 220 magazines only.
Mer...
Bättre Matning För Din Halvautomat
Ökat tryck stabiliserar följaren och förbättrar matningen, särskilt på magasin med hög kapacitet. SIG P220 ger 10% mer kraft i din äldre .45 ACP Sig P220 och är standardfjädern i nyare P220 med en grön rekylfjäder. Passar även Browning BDA .45 ACP. Separata modeller finns tillgängliga för magasin med metallbottenplatta (MF) eller plastbottenplatta (PF). Passar inte 8-rundors magasin tillverkade av Mec-Gar.
SPECIFIKATIONER: Passar inte Meg-Gar Sig 220 magasin och 70873 passar endast Sig 220 och BDA magasin med metallbottenplatta, 79383 passar endast Sig 220 magasin med plastbottenplatta.
Mer...
Kundernas betyg påWOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229
Antal betyg: 3
Från brownells.com: 3
Medelbetyg: 3,7
Doesn't work correctly(2017-09-08)
Standard (factory) Sig P220 magazines have 6 coils at the top that are wound smaller to fit inside the follower when compressed, and then get bigger on the lower coils. These springs are large coils for the entire length, so when compressed they do not fit inside the follower. This means they stack up below the follower and end up being too tall, which means you can't get 8 rounds in the magazine no matter how hard you try.
My suggestion is buy the replacement springs for 10-round P220 mags (which DO) have the smaller coils on top, and trim them so they have the same number of coils are the factory 8-round springs. Thats what I ended up doing, works great.
Just what was needed!!!(2011-09-16)
I recently purchased a few Mec-Gar extended capacity mags for my Sig P226 .40 cal. Straight out of the box, I noticed the mag springs were not strong enough to lock the slide back after firing the last round. I ordered the Wolff +10% and they were exactly what was needed! I haven't had one single malfunction or the slide failing to lock back since. A great low cost solution!
Restores old Sig magazines(2015-04-23)
Bought These for an older Sig P226 9mm from 1989 that was given to me. The old springs were the factory original and they didn't have a lot of power left in them. The new springs took them back to feeling like new magazines and I could feel the difference right away while loading and firing. Nice for the slide to lock open again when I'm empty.
Produktnr: 969000057 WOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229 Tillverkarens produktnummer: 74373 Ökat tryck stabiliserar följaren och förbättrar matningen, särskilt på magasin med hög kapacitet. SIG P220 ger 10% mer kraft i din äldre .45 ACP Sig P220 och är standardfjädern i nyare P220 med en grön rekylfjäder. Passar även Browning BDA .45 ACP. Separata modeller finns tillgängliga för magasin med metallbottenplatta (MF) eller plastbottenplatta (PF). Passar inte 8-rundors magasin tillverkade av Mec-Gar.
449SEK16449,00 kr
*
Levernastid ca. 14-21 dagar. Mer än 10 st. i centrallagret.
Funktioner:Make: Sig SauerModell: Universal HandgunsMängd: 3
Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se
Produktnr: 969000220 WOLFF +10% POWER SPRING, 3-PAK FITS SIG P220/BROWNING BDA MF Tillverkarens produktnummer: 70873 Ökat tryck stabiliserar följaren och förbättrar matningen, särskilt på magasin med hög kapacitet. SIG P220 ger 10% mer kraft i din äldre .45 ACP Sig P220 och är standardfjädern i nyare P220 med en grön rekylfjäder. Passar även Browning BDA .45 ACP. Separata modeller finns tillgängliga för magasin med metallbottenplatta (MF) eller plastbottenplatta (PF). Passar inte 8-rundors magasin tillverkade av Mec-Gar.
419SEK12419,00 kr
*
Levernastid ca. 14-21 dagar. Mer än 10 st. i centrallagret.
Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se
Produktnr: 969000222 WOLFF +10% POWER SPRING, 3-PAK FITS SIG P220/BROWNING BDA PF Tillverkarens produktnummer: 79383 Ökat tryck stabiliserar följaren och förbättrar matningen, särskilt på magasin med hög kapacitet. SIG P220 ger 10% mer kraft i din äldre .45 ACP Sig P220 och är standardfjädern i nyare P220 med en grön rekylfjäder. Passar även Browning BDA .45 ACP. Separata modeller finns tillgängliga för magasin med metallbottenplatta (MF) eller plastbottenplatta (PF). Passar inte 8-rundors magasin tillverkade av Mec-Gar.
Increased pressure stabilizes the follower and improves feeding, especially on high-capacity magazines. SIG P220 provides 10% more power in your older .45 ACP Sig P220 and is the factory standard spring in newer P220s with a green recoil spring. Also fits the Browning BDA .45 ACP. Separate models available for magazines with a metal floorplate (MF) or a plastic floorplate (PF). Will not fit 8-round magazines made by Mec-Gar.
SPECS: Will not fit Meg-Gar Sig 220 magazines and 70873 fits Metal Floor plate Sig 220 and BDA magazines only, 79383 fits Plastic Floor plate Sig 220 magazines only.
Mer...
Bättre Matning För Din Halvautomat
Ökat tryck stabiliserar följaren och förbättrar matningen, särskilt på magasin med hög kapacitet. SIG P220 ger 10% mer kraft i din äldre .45 ACP Sig P220 och är standardfjädern i nyare P220 med en grön rekylfjäder. Passar även Browning BDA .45 ACP. Separata modeller finns tillgängliga för magasin med metallbottenplatta (MF) eller plastbottenplatta (PF). Passar inte 8-rundors magasin tillverkade av Mec-Gar.
SPECIFIKATIONER: Passar inte Meg-Gar Sig 220 magasin och 70873 passar endast Sig 220 och BDA magasin med metallbottenplatta, 79383 passar endast Sig 220 magasin med plastbottenplatta.
Mer...
Kundernas betyg påWOLFF +10% POWER SPRING, 3-PAK FITS SIG HI-CAP P226, P228, P229
Antal betyg: 3
Från brownells.com: 3
Medelbetyg: 3,7
Doesn't work correctly(2017-09-08)
Standard (factory) Sig P220 magazines have 6 coils at the top that are wound smaller to fit inside the follower when compressed, and then get bigger on the lower coils. These springs are large coils for the entire length, so when compressed they do not fit inside the follower. This means they stack up below the follower and end up being too tall, which means you can't get 8 rounds in the magazine no matter how hard you try.
My suggestion is buy the replacement springs for 10-round P220 mags (which DO) have the smaller coils on top, and trim them so they have the same number of coils are the factory 8-round springs. Thats what I ended up doing, works great.
Just what was needed!!!(2011-09-16)
I recently purchased a few Mec-Gar extended capacity mags for my Sig P226 .40 cal. Straight out of the box, I noticed the mag springs were not strong enough to lock the slide back after firing the last round. I ordered the Wolff +10% and they were exactly what was needed! I haven't had one single malfunction or the slide failing to lock back since. A great low cost solution!
Restores old Sig magazines(2015-04-23)
Bought These for an older Sig P226 9mm from 1989 that was given to me. The old springs were the factory original and they didn't have a lot of power left in them. The new springs took them back to feeling like new magazines and I could feel the difference right away while loading and firing. Nice for the slide to lock open again when I'm empty.