45™ NO GUNSMITHING

957000035

If you have and older Ruger® MKI, MKII™ MK4 that's not drilled and tapped you can install this WEIG-A-TINNY® Scopemount without making any permanent alterations to your favorite pistol. Remove the rear sight, insert the threaded dovetail filler and install the mount with the screws provided. Accepts all Weaver style rings and accessories and most Picatinny rings and accessories. 5-1/4" long, silver or Black, matte anodized finish, weighs 2.5 ounces.

Mer...

Om du har en äldre Ruger® MKI, MKII™ eller MK4 som inte är borrade och gängade kan du installera detta WEIG-A-TINNY® siktesfäste utan att göra några permanenta ändringar på din favoritpistol. Ta bort bakre siktet, sätt i den gängade kilspårsfyllaren och installera fästet med de medföljande skruvarna. Accepterar alla Weaver-stils ringar och tillbehör samt de flesta Picatinny-ringar och tillbehör. 5-1/4" lång, silver eller svart, matt anodiserad finish, väger 71 gram.

Mer...

Kundernas betyg påWEIGAND COMBAT RUGER MK I, MK II, 22/451-PIECE BASE, BLACK

Antal betyg: 5
Från brownells.com: 5
Medelbetyg: 4,6

Gunsmith's Dream (2009-11-04)

The answer to mounting optics to Ruger MK I & MK II Pistols that are not drilled & taped at the factory (non adjustable sights). Just knock out the old sight install the provided dovetailed insert in it's place and fasten on the new base. Doesn't get any more simple than this and the base looks "like it belongs there". No modification to the receiver required.

Good Moiunt (2009-12-19)

I like everything about this mount except it is very tall. Raises the scope center point high above the bore center. This is not such a problem at long range but makes short range shooting more complicated (hold over changes drastically at short ranges.) Mid range trajectory goes higher above sight line than if sight were closer to bore center line. I think they could make this mount thinner. Overall well made, easy to install and solid well engineered. I would buy this again. Slight filing on the steel dovetail mounting block was required. A few light passes is all it took on mine. Tapped it into polace with brass punch.

Easy to Install - Solid Mount (2011-02-14)

I installed this mount on my Ruger 22/45 Target Model, and it went on with no issues. The mount is well finished and machined, and goes on without issue. Tap out existing rear sight with a no-mar removal tool or punch, insert the dovetail base, then attached with the provided screws. I mounted a Burris Fastfire II to it with no issues - works nicely and looks great. Main comment is that it would have been nice if an allen wrench (microscopic size) for the set screws for the base were included in the kit, but I managed to find one to fit them. I would recommend this mount for small red dot sights and very small handgun scopes, due to lack of front tie down screw (but no gunsmithing mods are needed with this rail!). Good product.

Great Service and Great Mount (2012-05-31)

Received the mount in 2 days! It fits exactly as stated. Just a slight tap from a small hammer and it went into the dovetail on my Ruger Mark I. You'll need a couple of Allen wrenches but we all have them anyway. I also used Locktite. Great product to mount a red dot scope on the pistol.

The way to go (2016-04-22)

As advertised, if you have a Ruger Mark I or Mark II and don't want to spend a lot of money having it drilled and tapped for a red dot or scope this is the way to go. Very good directions, simple to install and looks very good. I installed it on a Mark II, put a red dot on it, sighted it in and shot 100 rounds (at customer's request) with no movement of the rail. I call that "very good".

Läs 5 fler betyg på brownells.com

1049 1049 2 SEK

Produktnr: 957000035
WEIGAND COMBAT RUGER MK I, MK II, 22/451-PIECE BASE, BLACK
Tillverkarens produktnummer: RM2SMB Om du har en äldre Ruger® MKI, MKII™ eller MK4 som inte är borrade och gängade kan du installera detta WEIG-A-TINNY® siktesfäste utan att göra några permanenta ändringar på din favoritpistol. Ta bort bakre siktet, sätt i den gängade kilspårsfyllaren och installera fästet med de medföljande skruvarna. Accepterar alla Weaver-stils ringar och tillbehör samt de flesta Picatinny-ringar och tillbehör. 5-1/4" lång, silver eller svart, matt anodiserad finish, väger 71 gram.

1049 SEK 1 1 049,00 kr *

Levernastid ca. 14-21 dagar.
1 st. i centrallagret.

Funktioner: Basantal: 1-Piece Färg: Svart Make: Ruger Material: Aluminum Modell: Mark II Stil: Weaver-Style Bases

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Top takeaways

Installera WEIG-A-TINNY® siktesfäste utan att göra permanenta ändringar på Ruger® MKI, MKII™ eller MK4.
Accepterar alla Weaver-stils ringar och tillbehör samt de flesta Picatinny-ringar och tillbehör.
5-1/4" lång, svart matt anodiserad finish, väger 71 gram.

Produktinformation

Antal Baser: 1-Piece Färg: Svart Make: Ruger Material: Aluminum Modell: Mark II Stil: Weaver-Style Bases Leveransvikt: 0,068kg Leveranshöjd: 10mm Leveransbredd: 86mm Leveranslängd: 170mm

Produkt detaljer

Tillverkas i USA

Ansvarig ekonomisk aktör enligt EU-förordningen

Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se

Produktnr: 957201100
WEIGAND COMBAT RUGER MK I, MK II, 22/451-PIECE BASE, SILVER
Tillverkarens produktnummer: RM2SM Om du har en äldre Ruger® MKI, MKII™ eller MK4 som inte är borrade och gängade kan du installera detta WEIG-A-TINNY® siktesfäste utan att göra några permanenta ändringar på din favoritpistol. Ta bort bakre siktet, sätt i den gängade kilspårsfyllaren och installera fästet med de medföljande skruvarna. Accepterar alla Weaver-stils ringar och tillbehör samt de flesta Picatinny-ringar och tillbehör. 5-1/4" lång, silver eller svart, matt anodiserad finish, väger 71 gram.

1049 SEK 2 1 049,00 kr *