Varukorgen är tom.

Varukorg

Hjälp och kontakt

Fri frakt på beställningar över 2.999 kr

100 dagars returrätt

Nyhetsbrev

REA

Över 300 000 kunder - vi säger tack!

4,93/5 "Mycket bra" (1400+ recensioner)

40 000+ produkter inom jakt och skytte

BROWNELLS
REMINGTON 870 RIVET STAKING TOOL SET

050806105294 080612000

Takes The Pain Out Of Fitting The 2-Step Rivet

Two specially ground punches make fitting the 870 ejector spring and housing onto Remingtons' unique 2-step rivet a snap! The hole in the face of the #1 tool allows you to fasten the ejector housing to the receiver with the lower portion of the rivet. The #2 tool is then used to secure the ejector spring within the ejector housing with the upper portion of the rivet. Deluxe Kit combines the above two punches with an ejector spring rivet cutter that lets you take off just the peened area of the front rivet. Often lets you re-peen the existing rivet.

SPECS: Punches - Hardened steel, blue finish. 2 punches, each 3-½" (8.8cm) long. Rivet Cutter - Steel shaft and hardened steel cutter. 2-½" (6.3cm) long, .31" (7.8mm) shaft diameter, .143" (3.6mm) cutter diameter.

Mer...

Tar bort besväret med att passa 2-stegsniten

Två specialslipade stansar gör monteringen av 870 utkastarfjädern och boendet på Remingtons unika 2-stegsnit enkel! Hålet i ansiktet på #1 verktyget låter dig fästa utkastarboendet till mottagaren med den nedre delen av niten. Verktyg #2 används sedan för att säkra utkastarfjädern inuti utkastarboendet med den övre delen av niten. Deluxe Kit kombinerar de två ovanstående stansarna med en utkastarfjäder nitkutter som låter dig ta bort bara den utbredda delen av främre niten. Gör det ofta möjligt att återanvända den befintliga niten.

SPECS: Punches - Härdat stål, blått utförande. 2 stansar, varje 3-½" (8.8cm) långa. Rivet Cutter - Stålskaft och härdat stålskär. 2-½" (6.3cm) lång, .31" (7.8mm) skaftdiameter, .143" (3.6mm) skärdiameter.

Mer...

Kundernas betyg påBROWNELLS REMINGTON 870 RIVET STAKE TOOL SET

Antal betyg: 6
Från brownells.com: 6
Medelbetyg: 2,7

Good design, but too soft (2013-02-25)

The theory on these is quite sound. They worked well once I hardened the staking tools. They claimed they were hardened to begin with, I found them to be dead soft.

Works great! (2013-03-27)

Works great and is a must have along with spare parts if you plan to use your 870 as a wrol/shtf gun.

Easy to use and with good instructions. Had no problem with the hardening like the other gentlemen.

Right tool but one-time use (2015-07-21)

Let me start off by saying that this tool set is adequate if youâre just replacing the ejector spring. If you need to replace the entire ejector assembly this set might give you some trouble. First, the tip of the #1 punch was so wide that it didnât go all the way into the ejector channel. This prevented the punch from going far enough to fully seat the front rivet and left the entire assembly loose. I had to grind the tip down a little to make it narrow enough to bottom out on the inside of the ejector and fully seat the front rivet. Second, the depression in the tip of the #2 punch was too deep to upset the tip of the front rivet once the ejector spring was installed. Youâll have to use a flat punch that fits the ejector channel or do what I did and just use the #1 punch off-center. Lastly, the #2 punch has really thin side walls and mine split after just a few whacks on the rear rivet. A hardened tool should last for many installs. This was a one-time use tool. This set would be much better if they made some improvements. Itâs going back and I might just design my own set before my next 870 ejector install.

Replacing Ejector Rivets (2016-08-07)

Tools worked like they should, but the #1 staking tool split down the middle. #2 staking tool may last longer, but be careful.

<img width="500" src='/userdocs/reviewimages/17ad9880-337c-48d9-94b6-575a5fb49e0f.jpg' alt=''>

<img width="500" src='/userdocs/reviewimages/1f905f1a-4316-4955-b25c-f5a0d2599163.jpg' alt=''>

Did the job. Once. (2018-05-11)

I had made my own rivet stakes when I first replaced the ejector and spring (2-3/4 to 3" conversion) out of some hardened bolts (grade 5, maybe grade 8 would have worked better), but messed up the job and damaged my stakes. Decided to order this set along with new rivets because I didn't feel like fixing the stakes I made.

The stake with the large hole was useless. It didn't set the rear rivet at all, just mushroomed it a bit and didn't go down far enough to actually lock the ejector in place. I ended up using the flat side of the other stake to set the rear rivet and that worked just fine.

The stake with the small hole worked for the first stage of the front rivet, but the hole is so tight that after setting the rivet I had to clamp the stake in a vice and gently tap the receiver with a mallet to get the stake off the second stage of the front rivet. All while trying not to break it off. Very annoying. I ended up setting the second stage of the front rivet with a small punch from my regular punch set.

After setting the first stage of the front rivet the stake was deformed to the point that I would not be able to use it a second time.

I gave it two stars instead of one because the one stake does work for the two stage front rivet, but it was a one chance deal as the tool is now useless. Don't buy this if you want to add it to your tool set.

Just use a Home Depot punch (2018-08-01)

Bought this set to replace the ejector and ejector spring on my 870. After reading reviews, I was hesitant to buy but couldn't find any other tools on the market so I went ahead and bought this set. The tool for the rear rivet cracked down both sides and did not seat the rivet tight enough. I ended up using a standard punch to flatten the rivet. The tool for the front rivet didn't even fit inside the ejector. After some work with a Dremel tool I got the punch to fit and managed to hammer the first level of the front rivet flat. To flatten the second level of the front rivet I again used a standard punch since at this point the Brownell's punch was cracked.

The only reason this gets a 2 star review is that after calling Brownell's, they refunded my money. 5 stars for customer service, 1 star for the tool set.

Läs 6 fler betyg på brownells.com

649 1099 2 SEK

Produktnr: 080612000
BROWNELLS REMINGTON 870 RIVET STAKE TOOL SET
Tillverkarens produktnummer: RIVETSTAKTOOL 050806105294 Två specialslipade stansar gör monteringen av 870 utkastarfjädern och boendet på Remingtons unika 2-stegsnit enkel! Hålet i ansiktet på #1 verktyget låter dig fästa utkastarboendet till mottagaren med den nedre delen av niten. Verktyg #2 används sedan för att säkra utkastarfjädern inuti utkastarboendet med den övre delen av niten. Deluxe Kit kombinerar de två ovanstående stansarna med en utkastarfjäder nitkutter som låter dig ta bort bara den utbredda delen av främre niten. Gör det ofta möjligt att återanvända den befintliga niten.

649 SEK 21 649,00 kr *

Levernastid ca. 14-21 dagar.
Mer än 10 st. i centrallagret.

Funktioner: Make: Remington Modell: 870

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Top takeaways

Två specialslipade stansar för enkel montering av utkastarfjädern och dess boende på Remington 870.
Deluxe Kit inkluderar en nitkutter för att ta bort den utbredda delen av främre niten, vilket ofta möjliggör återanvändning.
Verktygen är tillverkade av härdat stål med blått utförande och inkluderar specifikationer för längd och diameter.

Produktinformation

Make: Remington Modell: 870 Leveransvikt: 0,045kg Leveranshöjd: 5mm Leveransbredd: 84mm Leveranslängd: 188mm UPC : 050806105294

Produkt detaljer

Tillverkas i USA

Ansvarig ekonomisk aktör enligt EU-förordningen

Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se

Produktnr: 080612001
BROWNELLS REMINGTON 870 DELUXE STAKING KIT 050806104310 Två specialslipade stansar gör monteringen av 870 utkastarfjädern och boendet på Remingtons unika 2-stegsnit enkel! Hålet i ansiktet på #1 verktyget låter dig fästa utkastarboendet till mottagaren med den nedre delen av niten. Verktyg #2 används sedan för att säkra utkastarfjädern inuti utkastarboendet med den övre delen av niten. Deluxe Kit kombinerar de två ovanstående stansarna med en utkastarfjäder nitkutter som låter dig ta bort bara den utbredda delen av främre niten. Gör det ofta möjligt att återanvända den befintliga niten.

1099 SEK 10 1 099,00 kr *

Levernastid ca. 14-21 dagar.
Mer än 10 st. i centrallagret.

Funktioner: Make: Remington Modell: 870

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Effektivisera din Remington 870 med vårt Rivet Staking Tool Set! 🛠️ Inkluderar specialstansar för enkel montering och återanvändning.

Takes The Pain Out Of Fitting The 2-Step Rivet

Mer...

Tar bort besväret med att passa 2-stegsniten

Mer...

Kundernas betyg påBROWNELLS REMINGTON 870 RIVET STAKE TOOL SET

Antal betyg: 6
Från brownells.com: 6
Medelbetyg: 2,7

Good design, but too soft (2013-02-25)

The theory on these is quite sound. They worked well once I hardened the staking tools. They claimed they were hardened to begin with, I found them to be dead soft.

Works great! (2013-03-27)