Varukorgen är tom.

Varukorg

Hjälp och kontakt

Fri frakt på beställningar över 2.999 kr

100 dagars returrätt

Nyhetsbrev

REA

Över 300 000 kunder - vi säger tack!

4,93/5 "Mycket bra" (1400+ recensioner)

40 000+ produkter inom jakt och skytte

DAVID TUBB
M14 & M1A SEMI-AUTO CHROME SILICON RIFLE SPRINGS

840000037

Stable Performance For 500,000 Compression Cycles

Factory weight, chrome silicon spring kit restores reliable function and long-lasting performance to the M1A and M14. Op rod spring helps ensures consistent cycling; hammer spring gives repeatable sear engagement for a clean breaking trigger.

SPECS: Chrome silicon steel. Op Rod Spring - 15-3⁄4" (40cm) long. Hammer Spring - 2-1⁄4" (5.7cm) long. Fits M1A and M14.

Mer...

Stabil prestanda för 500 000 kompressionscykler

Fabriksvikt, kromsilikonfjäderkit återställer pålitlig funktion och långvarig prestanda till M1A och M14. Op rod-fjädern säkerställer konsekvent cykling; hammarefjädern ger upprepbar avtryckarkontakt för en ren och skarp avfyrning.

SPECS: Kromsilikonstål. Op Rod Spring - 15-3⁄4" (40cm) lång. Hammer Spring - 2-1⁄4" (5.7cm) lång. Passar M1A och M14.

Mer...

Kundernas betyg påDAVID TUBB M1A OP ROD/HAMMER SPRING SET

Antal betyg: 7
Från brownells.com: 7
Medelbetyg: 4

Great Set of Springs (2010-06-23)

These springs were high quality and worked well in replacing stock Springfield Springs. You might as well get the Sadlak Match Op Rod Guide while you are at it. It is round as opposed to flat metal and keeps the spring from kinking.

No for a M1 Garand (2010-10-15)

I purchased 3 sets of these for rebuilding CMP Garands.I found the Op Rod springs to have the wrong tension as none of the 3 worked in any combination in even my already function M1 Garands.Instead I installed new Mil Spec springs.They worked fine right out of the Mailbox.[...]

I'll have to try it out. (2010-10-25)

I just did a review that it's not for the Garand, but the small print says " - also fits M1 Garand rifles". David Tubb put his name on it so I will give it a try in my Garand.

These are not for Garand (2011-03-31)

Despite what the copy says, these springs are for the M14 and M1A rifles, not for the M1 Garand.

Could someone at Brownells please correct the copy, removing the references to "M1" and "Garand"?

Repeat, the M1A/M14 takes a different op rod spring from the M1 Garand.

A must have (2013-03-10)

Ive used several different recoil springs in my M14 and there are several better choices over the stock spring available. The Tubbs springs are a little more expensive than some others out there, but I have not found anything that performed better than these recoil springs.
Ive found the use of this spring, along with a Sadlak recoil spring guide to significantly improve the performance of a M14/M1A.

Great product, smooth function (2014-03-01)

Fits and works well. The hammer spring is a bit harder to install, but doable. Not sure where people mistakenly think this works on a Garand, perhaps Brownells corrected the description? Yes, they make one for the M1 Garand, but a completely different part number. This is only for the M14/M1A.

If you have an M1A, you need to upgrade to these springs.

Great upgrade (2015-02-27)

A great set of springs especially when paired with a Sadlak national match spring guide. Do your M1A a favor and pick these up. Greatly improved cycling, nice and smooth.

Läs 7 fler betyg på brownells.com

0 0 1 SEK

Produktnr: 840000037
DAVID TUBB M1A OP ROD/HAMMER SPRING SET
Tillverkarens produktnummer: CSM1A Fabriksvikt, kromsilikonfjäderkit återställer pålitlig funktion och långvarig prestanda till M1A och M14. Op rod-fjädern säkerställer konsekvent cykling; hammarefjädern ger upprepbar avtryckarkontakt för en ren och skarp avfyrning.

Meddela om tillgänglighet

Ej tillgänglig.

Funktioner: Make: Springfield Modell: M1 Garand

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Produktinformation

Make: Springfield Modell: M1 Garand Leveransvikt: 0,045kg Leveranshöjd: 4mm Leveransbredd: 118mm Leveranslängd: 196mm

Produkt detaljer

Tillverkas i USA

Återställ pålitlig funktion med M14 & M1A kromsilikonfjäderkit. ⚙️ Perfekt för skarp avfyrning och långvarig prestanda. Beställ nu!

Stable Performance For 500,000 Compression Cycles

SPECS: Chrome silicon steel. Op Rod Spring - 15-3⁄4" (40cm) long. Hammer Spring - 2-1⁄4" (5.7cm) long. Fits M1A and M14.

Mer...

Stabil prestanda för 500 000 kompressionscykler

SPECS: Kromsilikonstål. Op Rod Spring - 15-3⁄4" (40cm) lång. Hammer Spring - 2-1⁄4" (5.7cm) lång. Passar M1A och M14.

Mer...

Kundernas betyg påDAVID TUBB M1A OP ROD/HAMMER SPRING SET

Antal betyg: 7
Från brownells.com: 7
Medelbetyg: 4

Great Set of Springs (2010-06-23)

No for a M1 Garand (2010-10-15)

I'll have to try it out. (2010-10-25)

I just did a review that it's not for the Garand, but the small print says " - also fits M1 Garand rifles". David Tubb put his name on it so I will give it a try in my Garand.

These are not for Garand (2011-03-31)

A must have (2013-03-10)

Great product, smooth function (2014-03-01)

Great upgrade (2015-02-27)

A great set of springs especially when paired with a Sadlak national match spring guide. Do your M1A a favor and pick these up. Greatly improved cycling, nice and smooth.

Läs 7 fler betyg på brownells.com