Över 300 000 kunder - vi säger tack!

40 000+ produkter inom jakt och skytte

Mät headspace enkelt med Hornady LOCK-N-LOAD™ Gauge Tool! 🔧 Perfekt för handladdare som vill optimera sina hylsor. Köp nu!

HORNADY LOCK-N-LOAD™ HEADSPACE GAUGE TOOL - HORNADY LOCK-N-LOAD HEADSPACE KIT WITHOUT BODY

090255704792 749004278

Varianter:

Produktnr: 749004278
Slut i lager
549 SEK 0 549 kr *
Produktnr: 749005148
Slut i lager
799 SEK 50 799 kr *
0 0 2 SEK

Varianter:

Produktnr: 749004278
Slut i lager
549 SEK 0 549 kr *
Produktnr: 749005148
Slut i lager
799 SEK 50 799 kr *

Beskrivning:

Visa original (engelska)
Detta prisvärda headspace-mätverktyg från Hornady Lock-N-Load Products (tidigare Stoney Point) möjliggör för handladdaren att mäta förändringar i headspace på patroner med en dial/digital skjutmått. Olika bussningsstorlekar (beroende på patronfamilj) sätts in i Hornady Lock-N-Load Comparator Body, som fästs vid ett skjutmått. Handladdaren kan sedan mäta förändringarna mellan avfyrad och storleksanpassad mässing. Detta gör att handladdaren kan justera sina storleksverktyg för en korrekt passform i sin kammare. När en handladdare överdimensionerar sina hylsor kan det orsaka överdrivna headspace-problem, varav ett är att förkorta livslängden på mässingen. Hornady Lock-N-Load Headspace Gauge Set gör det möjligt för användaren att mäta mässing från hylshuvudet till datalinjen på hylsans axel. Fem bussningsstorlekar gör att du kan mäta headspace på de flesta flaskhalspatroner från 17 Remington till de bältesmagnum. Bussningarna säljs antingen med Comparator Body eller utan Comparator Body (för de som redan har en). Se Hornady Gauge Bushing Chart.

Top takeaways

  1. Hornady Lock-N-Load Headspace Gauge Tool låter handladdare mäta förändringar i patronernas headspace med ett skjutmått.
  2. Verktyget inkluderar fem olika storlekar på bussningar, vilket gör det möjligt att mäta headspace på de flesta flaskhalspatroner från 17 Remington till bältesförsedda magnumkalibrar.
  3. Bussningarna kan köpas med eller utan Comparator Body, beroende på om användaren redan har en.

Produktinformation

  • Patron: Universal
  • Leveransvikt: 0,113kg
  • Leveranshöjd: 41mm
  • Leveransbredd: 97mm
  • Leveranslängd: 155mm
  • UPC: 090255704792

Produkt detaljer

Tillverkas i USA

Kundrecensioner

Kundbetyg (3)

5 / 5
Rekommenderar varmt

Brownells USA Saves your brass 2016-03-04

I purchased these once I started loading the less common calibers (more specific 6.5 Grendel). When brass is .70/piece for decent brass, you want it to last a while. Since this was an auto loader, it's hard on brass. I was WAY oversizing my brass by putting it back to factory specs. I set the dies up according to manufacture recommendations, and it worked as it should. However, I noticed on the 3rd and 4th firings, the brass would start to harden (needed to be annealed) and when I full length sized them, it would leave a ring of brass around the base of the case. I knew this was killing my cases and my pocket book. I purchased this kit so I would bump the shoulders back (.003" per the recommended for auto loaders) and it works like a charm. I have been able to get 7 or 8 firings before the brass needs annealed because it's being worked so much less in the chamber. This also eliminates the need for a neck sizer as well. When shooting my bolt actions, I used to neck size as long as I could, but eventually, you have to size it back down because the shoulder expands enough to cause issues. When you use these, you can set up your FL sizer to bump the shoulder back .001" and it's very easy to chamber, and each case is the exact same, so no need to worry about variations in your load. I can't believe I waited as long as I did to purchase this tool. This should have been purchased at the beginning/learning stages of my reloading obsession and I would have been much better off!

Rekommenderar varmt

Brownells USA Complete set for all calibers... 2015-09-30

A complete set of headspace gages (for setting headspace by gaging the shoulder datum on a bottleneck cartridge. It ships with an anvil that attaches to the jaw of your dial/digital caliper and I use the anvil with custom made gages for determining cartridge overall length (measured on the bullet ogive), the most accurate and repeatable method).



Absolutely necessary for determining the amount of 'bump back' to set your die at to attain easy bolt lift and no brass wipe on the bolt face.

Visste du?

Tillverkarinformation

Ansvarig ekonomisk aktör enligt EU-förordningen

Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se

Oj! Något gick fel.

Vi stötte på ett fel när vi laddade innehållet. Vänligen uppdatera sidan för att fortsätta. Om problemet kvarstår, kontakta vår kundtjänst.

Tillbaka till toppen