876430008981 Enkel konstruktion förenar ringen och basen till en enhet. Genom att eliminera ring/bas-joint hålls vikten till ett minimum och ger en starkare montage. Varje ringlock är 5⁄8" bred, med fyra TORX-skruvar, för att hålla stora kikarsikten på plats utan att glida eller flytta sig. Designad av Mel Forbes från New Ultralight Arms.
Lagervara
Levernastid ca. 14-21 dagar. 2 st. i centrallagret.
Levernastid ca. 14-21 dagar. 2 st. i centrallagret.
When Every Ounce Counts; The Strength Of Steel Without The Weight
One-piece construction blends the ring and base into a single unit. Eliminating the ring/base joint not only keeps weight to a minimum, it provides a stronger mount. Each ring cap is 5⁄8" wide, with four, TORX screws, to keep large scopes from slipping or shifting. Designed by Mel Forbes of New Ultralight Arms.
SPECS: 7000 series aluminum, black, anodized, matte finish. Accepts 1" dia. scopes, unless otherwise listed in fits column for 30mm dia. scopes. Height from bottom of ring to top of receiver: Low - .400" (10.1mm), Med - .500" (12.7mm). High - .640" (16.3mm), X‑High - .740" (18.8mm). Approx. weight 2.1 oz. (59 g). Some heights vary, see chart below. Rem. 700 also fits 721/722/725 and 40X models. Rem. Model Seven fits receivers with four screw holes. Savage AccuTrigger fits round top centerfire receivers with AccuTrigger. Win. 70 fits .860" rear hole spacing only.
När varje uns räknas; Styrkan av stål utan vikten
Enkel konstruktion förenar ringen och basen till en enhet. Genom att eliminera ring/bas-joint hålls vikten till ett minimum och ger en starkare montage. Varje ringlock är 5⁄8" bred, med fyra TORX-skruvar, för att hålla stora kikarsikten på plats utan att glida eller flytta sig. Designad av Mel Forbes från New Ultralight Arms.
SPECS: 7000-seriens aluminium, svart, anodiserad, matt finish. Accepts 1" dia. kikarsikten, om inte annat anges i passande kolumn för 30mm dia. kikarsikten. Höjd från botten av ringen till toppen av mottagaren: Low - .400" (10.1mm), Med - .500" (12.7mm). High - .640" (16.3mm), X‑High - .740" (18.8mm). Ungefärlig vikt 2.1 oz. (59 g). Vissa höjder varierar, se diagrammet nedan. Rem. 700 passar även 721/722/725 och 40X modeller. Rem. Model Seven passar mottagare med fyra skruvhål. Savage AccuTrigger passar runda toppar på centerfire-mottagare med AccuTrigger. Win. 70 passar endast .860" bakre hålavstånd.
Top takeaways
Ett stycke konstruktion som smälter samman ring och bas till en enda enhet för en starkare och lättare montering.
Varje ringlock är 5⁄8" brett med fyra TORX-skruvar för att förhindra att stora sikten glider eller förskjuts.
Tillverkad av 7000-seriens aluminium, svart anodiserad matt finish, designad för Browning X-Bolt med 30mm kikarsikte tubdiameter.
Produktinformation
Elevation:0 MOA
Finish:Svart
Höjd:.640'',.715''
Kikarsikte tubdiameter:30mm
Modell:X-Bolt
Stil:Direct Mount
Vapentyp:Browning
Leveransvikt:0,116kg
Leveranshöjd:67mm
Leveransbredd:72mm
Leveranslängd:199mm
UPC:876430008981
Produkt detaljer
Tillverkas i USA
Kundrecensioner
Kundbetyg (14)
4,9 / 5
Rekommenderar varmt
best tikka rings I have seen 2018-11-12
Rekommenderar varmt
The BEST I've found for 10/22's. 2014-05-01
I've installed these rings on 5 or 6 guns now. These are the nicest looking and best working scope mounts I have found for 10/22's if you want a nice traditional look and you're sick of seeing miles of picatinny rail on every gun you own. They are offset so you can reverse each one to get good positioning on the scope tube (as close to the occular and objective lenses as possible while staying away from the erector tube area), they are very well finished, easy to install, line up perfectly and are very sturdy. Order the MEDIUM height for any scope with an objective between 51 and 57 mm. Order LOW height for scopes 50 mm and under. Good shootin'!!
Rekommenderar varmt
Perfect 2014-01-23
Mounting a Leupold 6.5-20x40 on a Savage 12 BJTV w/ thumbhole stock and needed the scope as low as possible. These low extended rings were THE PERFECT solution. Scope is now EXACTLY where I wanted it.
I have 4 sets of Talley rings on 4 separate rifles and could not ask for better rings. Best rings for the dollar out there.
Rekommenderar varmt
Delightfully clean 10/22 scope mounts 2013-08-10
These scope mounts for the Ruger 10/22 are absolutely elegant. Let me share some background info that can help make this relevant to everyone who appreciates 10/22s.
I love 10/22s -- at the moment I have five. I tweak and tune the daylights out of them for both performance and appearance. I'm fond of the contour of the 10/22 receiver and feel Ruger's furnished mount base spoils the lines. For this reason I've made small one-piece bases for my halographic red dots and small two-piece bases for scopes and tube-type red dots -- all starting from Ruger's base.
With the Talley bases, this is no longer necessary. They cover a minimum of the top of the receiver. They're beautifully made and finished. And they hold a scope tightly without marring the finish.
My only wish is that they were also available in a silver finish. They'd look spectacular with my silver Ultradot red dots on my stainless10/22s. I might buy additional black ones and send them off to be reanodized silver. I like them that much.
Rekommenderar varmt
GREAT RINGS 2013-01-10
THEY ARE TRUE, LITE, AND HAVE TORX SCREWS SO THEY CAN BE REMOVED AND TIGHTENED MANY TIMES IF NEEDED. 25#S OF TORQUE IS PLENTY. GREAT PRODUCT.
Rekommenderar varmt
Excellent Product 2012-07-09
These are the best rings I have found for my custom Mauser rifles. The finish is good enough I do not need to polish and re-finish to make them match the Matte finish of Leupold scopes. They are better than some of the more costly rings I have bought and have built in bases so one less thing to buy.
Rekommenderar varmt
excellant 2011-10-28
I used these to install a Bushnell Elite scope on my Browning A bolt. The rings fit perfectly and are very secure.
Rekommenderar varmt
Great Rings! 2011-08-23
Used this to mount a varmint scope (42mm objective) on my Anschutz 1732 in .22 Hornet. Height was perfect for this application, leaving only a few millimeters of space between the barrel and scope. A bigger objective scope would require higher rings. Easy to install, well made, and rock solid mount and ring combination.
Rekommenderar varmt
A-Bolt LW Scope Mount 2010-11-20
I used these to mount a 2.5 X 8 Leupold on a 20" Micro Hunter. They're extremely light, but appear to be rugged. The fit is perfect, the scope lined up very square, no need for lapping. I torqued the base screws @ 30 inch/lbs and a touch of blue loctite. The ring screws were evenly torqued @ 22.5. They compliment the clean lines of the little carbine without sacrificing quality. It placed the scopes objective about 1/4" above the barrel, and allowed more than an ample amount of placement for eye relief. I'm sold.
Rekommenderar med reservationer
Great quality, not very 2010-09-28
Wanted to replace the medium-height rings that came with my Tikka T3 in 6.5x55 with some that were stronger and lower. I prefer to use a 2-7x32 scope and like to mount it nice and low. The Talley "low" rings, while very strong and well-made, appear to have enough room for a 40mm objective lens scope. They don't appear to be any lower than the factory rings. Other than that (and some embarrassing typos on the packaging), they are great.
Rekommenderar varmt
Perfect fit for short action 2010-03-07
I mounted these on a Winchester Ranger short action and the fit is perfect. I tried a few other brands, two-piece bases overlapped the action area and one-piece bases did not fit (the ranger action is a bit shorter than a standard short action). They look great on the gun and alignment was right on. No shims required.
Rekommenderar varmt
Long-term Test 2010-01-16
I put a set of these on my Tikka in .338 Winchester magnum several years ago after the "B" brand failed to hold the scope. My hunting load sends a 225 gr bullet out the muzzle at 2900 fps over my Oehler chrono; there is recoil. The Talley lightweights hold the Zeiss 3.5-10X scope absolutely rock solid year after year of hard hunting use in Montana. This is a quality product.
Rekommenderar varmt
THE BEST - BAR NONE 2009-12-07
I have sixteen scoped guns and have experience with a number of name brand manufacturers of bases and rings. Tally makes a product that is simple to install and, at least in my case, needed no shimming or adjustments to align the rings which I check with a Sinclair Scope Alignment Tool. So far I have mounted three scopes with Tally mounts with no problem. Nuff said.
Rekommenderar varmt
Great Product 2009-10-07
I was sort of skeptical about how these would work (no allowance for adjustments), but I heard a good report about Talley, so I gave them a shot. Great fit and finish, and no adjustment needed. In fact, the positional tolerances on these things are so good, that my scope needed less adjustment than with any other type of mounting system I've used lately. Note: For the medium height setup, a 40mm scope is the max. diameter for the Marlin 336.
Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se
Säkerhetsinstruktioner för LIGHT WEIGHT SCOPE MOUNT TALLEY BROWNING XBOLT HIGH 30MM SCOPE MOUNTS
Introduktion
Tack för att du valt LIGHT WEIGHT SCOPE MOUNT TALLEY BROWNING XBOLT HIGH 30MM SCOPE MOUNTS. Denna produkt är utformad för att ge en säker och stabil montering av kikarsikten på din Browning XBolt. För att säkerställa säker användning och långvarig prestanda, vänligen följ dessa säkerhetsinstruktioner noggrant.
Allmänna säkerhetsriktlinjer
Säkerställ att produkten är avsedd för användning med din specifika modell av Browning XBolt.
Kontrollera att alla delar är intakta och inte skadade innan installation.
Använd produkten endast för dess avsedda syfte.
Förvara produkten utom räckhåll för barn och sårbara grupper.
Rapportera eventuella skador eller defekter till tillverkaren.
Specifika säkerhetsåtgärder vid användning
Använd alltid rätt verktyg för installation av montaget.
Följ installationsanvisningarna noggrant för att undvika skador på produkten eller vapnet.
Undvik att överdriva åtdragningen av skruvarna för att förhindra skador på ringen eller basen.
Kontrollera regelbundet att montaget är säkert och att inga delar har lossnat.
Använd kikarsikten som är kompatibla med 30mm tubdiameter.
Instruktioner för installation och användning
Förberedelse:
Samla alla nödvändiga verktyg, inklusive TORXskruvmejsel.
Kontrollera att montaget är i gott skick och att inga delar saknas.
Installation:
Placera basen på mottagaren i enlighet med tillverkarens anvisningar.
Använd TORXskruvarna för att fästa ringen på basen. Se till att skruvarna är jämnt åtdragna.
Kontrollera att kikarsiktet är korrekt placerat och justerat innan du fäster det helt.
Användning:
Efter installationen, kontrollera att kikarsiktet sitter fast ordentligt.
Justera kikarsiktet efter behov för att säkerställa noggrannhet.
Använd alltid produkten i enlighet med gällande vapenlagar och säkerhetsföreskrifter.
Avfallshanteringsinstruktioner
Avlägsna och kassera förpackningsmaterial på ett miljövänligt sätt.
Om produkten är skadad eller inte längre behövs, följ lokala riktlinjer för avfallshantering av metall och plast.
Kontakta lokala myndigheter för information om korrekt avfallshantering.
Kontaktinformation för vidare support
För frågor eller support angående produkten, vänligen kontakta tillverkaren direkt. Se förpackningen eller produktens officiella webbplats för mer information.
Tack för att du följer dessa säkerhetsinstruktioner. Genom att göra det bidrar du till en säker och effektiv användning av din LIGHT WEIGHT SCOPE MOUNT TALLEY BROWNING XBOLT HIGH 30MM SCOPE MOUNTS.