Uppgradera ditt Remington 700 med HUNTER 700 MAG WELL! 🔥 Enkel installation för avtagbara boxmagasin. Perfekt för jägare och skyttar!
MAGPULHUNTER 700 SHORT ACTION MAGAZINE WELL BOTTOM METAL - MAGPUL HUNTER 700 MAG WELL BOTTOM METAL FOR REMINGTON 700 SA BLACK
840815100768100016665
Top takeaways
Magpul Bolt Action Magazine Well är en färdig lösning för Remington 700 Hunter Stock som möjliggör användning av avtagbara boxmagasin.
Installationen kräver endast borttagning av OEM bottenmetall och insatsen på Hunter 700 Stock, utan behov av specialanpassning från vapensmeder.
Designad för att fungera med AICS-mönster, korta actionmagasin och inkluderar Magpul PMAG 5 AC.
Produktinformation
Finish:Svart
Modell:700
Vapentyp:Remington
Leveransvikt:0,259kg
Leveranshöjd:51mm
Leveransbredd:140mm
Leveranslängd:203mm
UPC:840815100768
Produkt detaljer
Tillverkas i USA
USA: s exportklassificering: 0A501.x
Specifikationer:
Finish: Svart
Make: Remington
Modell: 700
119911991SEK
1199SEK1 199 kr
Priser inkl. moms, exkl. frakt
Produktnr: 100016665
Tillv.nr.: MAG497-BLK
840815100768 Magpul Bolt Action Magazine Well är en enkel lösning för vår Remington 700 Hunter Stock för dem som vill lägga till avtagbara boxmagasin till sin bössa. Genom att enkelt ta bort din OEM bottenmetall och insatsen på Hunter 700 Stock kan användare lägga till detta förstärkta polymertryckskydd och magasinbrunn till sin bössa utan behov av anpassad inpassning från vapensmeder. Utformad för att fungera med AICS-mönster, korta actionmagasin. Detta kit inkluderar även Magpul PMAG 5 AC.
Lagervara
Levernastid ca. 14-21 dagar. Mer än 10 st. i centrallagret.
Levernastid ca. 14-21 dagar. Mer än 10 st. i centrallagret.
The Magpul Bolt Action Magazine Well is a drop-in solution for our Remington 700 Hunter Stock for those that are wishing to add detachable box magazine capabilities to their rifle. By simply removing your OEM bottom metal and the insert on the Hunter 700 Stock, users can add this reinforced polymer trigger guard and magazine well to their rifle without the need for custom inletting from gunsmiths. Designed to work with AICS pattern, short action magazines. This kit also includes the Magpul PMAG 5 AC.
Magpul Bolt Action Magazine Well är en enkel lösning för vår Remington 700 Hunter Stock för dem som vill lägga till avtagbara boxmagasin till sin bössa. Genom att enkelt ta bort din OEM bottenmetall och insatsen på Hunter 700 Stock kan användare lägga till detta förstärkta polymertryckskydd och magasinbrunn till sin bössa utan behov av anpassad inpassning från vapensmeder. Utformad för att fungera med AICS-mönster, korta actionmagasin. Detta kit inkluderar även Magpul PMAG 5 AC.
Top takeaways
Magpul Bolt Action Magazine Well är en färdig lösning för Remington 700 Hunter Stock som möjliggör användning av avtagbara boxmagasin.
Installationen kräver endast borttagning av OEM bottenmetall och insatsen på Hunter 700 Stock, utan behov av specialanpassning från vapensmeder.
Designad för att fungera med AICS-mönster, korta actionmagasin och inkluderar Magpul PMAG 5 AC.
Produktinformation
Finish:Svart
Modell:700
Vapentyp:Remington
Leveransvikt:0,259kg
Leveranshöjd:51mm
Leveransbredd:140mm
Leveranslängd:203mm
UPC:840815100768
Produkt detaljer
Tillverkas i USA
USA: s exportklassificering: 0A501.x
Kundrecensioner
Kundbetyg (12)
4 / 5
Rekommenderar varmt
Great for the money 2018-01-04
This product is great, not perfect, but great. Feeding is reliable and loading is fast. Install is supper easy and fast, mags are decent quality. Its a $70 remington 700 mag conversion that works. The quality is not up to accuracy international or Wyatts standers but its not $250 either.
Rekommenderar varmt
Another Excellent Magpul Product 2016-11-13
I finally have the ability to use a box magazine with my Rem 700. I had my eye on the Pro Hunter stock since it came out but was sold when I came across this at my local gun store; I picked up the stock and bottom 'metal'. Easy swap out and works great. Too bad the magazines are AICS and not just the standard 308 PMAG. At least it comes with a 5 round magazine.
Rekommenderar med reservationer
It works, but in not drop-in 2016-10-15
Basically , this stock is a great design with two minor flaws. Number one is that this trigger guard rattles around inside the stock. It really requires a little bit of superglue or some sort of adhesive to bond it onto the stock and take out the slack. The second is that the trigger guard has to be inletted on the inside back side to allow the trigger too pull to the rear. It took me about an hour of unnecessary fooling with it in order to get it working right. A slight redesign seems in order. I tried it with a Jard trigger, a Timney trigger and the factory X-mark trigger and they all hit on the back of the trigger guard and would not function without modification.
Rekommenderar varmt
Great product 2016-08-06
Drop in fit for my 700. Excellent value over the $500 aluminum options. Makes reloads faster with my scope setup. Should have put this in a while ago for the price. Highly recommended.
Rekommenderar
Economical mag conversion for drop plate 2016-03-29
I have the same complaint as others about the trigger guard contacting the trigger. I plan on sanding it down for some extra clearance. So far the trigger breaks, but it does make contact with the guard. A rounded profile would have been a better option in this case. The stock and mag well make a nice upgrade for the original drop plate setup and how much of a PITA that is to load.
Rekommenderar varmt
Guess I got a good one 2016-03-26
After reading the other reviews on this product, I guess that I lucked out. Mine fits perfectly, and functions flawlessly. I can't ask for anything more. Especially for a little over 60 bucks. I had it installed in under a minute because it came in with my stock. Everything lined up right, and it cycles rounds great. I can't say that my mag release is hard. I honestly wouldn't want it any easier for fear that it would be bumped easily. I had no clearance issues with my trigger either. I have the x-mark pro in there still, but have seen many reviews that the Timney 510 will fit in there with no problem. As long as there is a curve, it should fit. Once again, maybe I got lucky, but I doubt it. I seem to be cursed in all things gun related, and mine works great.
Rekommenderar varmt
Vast improvement 2016-02-12
I installed this with the Magpul Hunter 700 stock on a Remington 700 AAC-SD to replace the factory stock and an aftermarket magazine conversion kit that I had bought sometime back. I ordered two new bolts (stainless steel) for the installation and it took less than 10 minutes to swap out the old stock with the new one and the magazine conversion. The magazines fit snug and held firmly in place. There is no magazine rock so they rounds feed smoothly and do not jamb.
Rekommenderar inte
Back of trigger guard touches trigger 2016-02-11
When the mag well was installed on the bench, the trigger was close to the trigger guard and had just a few thousandths of clearance. After two rounds fired at the range, the rifle seated into the Magpul Hunter stock and the trigger was bound on the trigger guard. Could not get a third round to fire. Must either modify the trigger guard by filing the back (slanted portion) or replace the Remington trigger with a strait trigger or file off the bottom 1/4 inch of the trigger. The defect in design appears to be the rear of the trigger guard has a 45 degree slant to it when it should have more of a radius to allow for the trigger pull.
Rekommenderar inte
Mag well too tight for AI mags. 2016-01-02
The mag well does not accept AI magazines or aftermarket AI style magazines. This seems to function with the Magpul 308 mag that was supplied, however, I was looking to adapt this to a 223 mag. Also the trigger guard is too small to accept anything other than the factory trigger. The mag release is clumsy and requires an enormous amount of pressure to release. I am sending this back with the Magpul hunter stock. I will wait for the second generation from Magpul with hopes that they rectify their design shortcomings.
Rekommenderar varmt
Works Great 2015-12-01
Everything dropped into place. The rounds feed smooth as glass. I have the Remington factory trigger so there was no trigger issues. Shoots good, love it.
Rekommenderar
Mostly good 2015-11-25
Pros: Looks great. Comes with the magazine.
Con: The mag release tension is out of this world. A lot more than it should be. Also, it doesn't fit the flat triggers.
Rekommenderar varmt
Good stuff 2015-11-16
I really like the stock and mag well. My main uses are hunting and target shooting. Solid, quality feel one would expect from magpul. My only complaint is the trigger guard on this mag well does NOT quite clear my Timney straight trigger. Nothing a few minutes with the dremmel couldn't fix, but worth noting.
Uppgradera ditt Remington 700 med HUNTER 700 MAG WELL! 🔥 Enkel installation för avtagbara boxmagasin. Perfekt för jägare och skyttar!
Destination Control Statement: Dessa poster styrs av USA: s regering och godkänns endast för export till det land där den slutliga destinationen används av den slutliga mottagaren eller slutanvändaren som identifierats här. De får inte vidareförsäljas, överföras eller på annat sätt kasseras till något annat land eller någon annan än den godkända slutliga mottagaren eller slutanvändaren, antingen i sin ursprungliga form eller efter att ha monterats i andra föremål utan att först få godkännande från den amerikanska regeringen eller som annars är tillåten enligt amerikansk lag och förordningar.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Destination Control Statement: Dessa poster styrs av USA: s regering och godkänns endast för export till det land där den slutliga destinationen används av den slutliga mottagaren eller slutanvändaren som identifierats här. De får inte vidareförsäljas, överföras eller på annat sätt kasseras till något annat land eller någon annan än den godkända slutliga mottagaren eller slutanvändaren, antingen i sin ursprungliga form eller efter att ha monterats i andra föremål utan att först få godkännande från den amerikanska regeringen eller som annars är tillåten enligt amerikansk lag och förordningar.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Magpul Remington 700 Hunter Stock är tillverkad av förstärkt polymer och anodiserad A380 gjuten aluminiumbäddblock, vilket ger förbättrad ergonomi och justerbar längd och kamhöjd.
Kolven är en "drop-in"-lösning för Remington 700 Short Actions och kräver ingen bedding, samt är M-LOK-kompatibel för olika tillbehör.
Tillbehör som Magpul SGA Recoil Pad Adapter och Magpul SGA Cheek Riser Kit säljs separat, likaså Bolt Action Magazine Well för användning med avtagbara boxmagasin.
PMAG 10 7.62 AC är ett pålitligt och hållbart polymermagasin, kompatibelt med .308 Winchester-patroner.
Magasinet har en kapacitet på 10 rundor, vilket är dubbelt så mycket som standard 5-rundare, och är idealiskt för tävling eller stridsbruk.
Tillverkat med avancerad M3-teknologi, erbjuder magasinet fler funktioner och hög tillförlitlighet för repetergevär.
Magpul M-LOK Bipod Mount möjliggör montering av bipods med Harris-stilens fästmönster och erbjuder en lågprofilerad och robust lösning.
Fästet sitter närmare monteringsytan än traditionella M1913 bipodfästen, vilket ger överlägsen styrka och stabilitet.
Tillverkad av mil-spec anodiserad aluminium, har fasade ändar och hörn för att minska vassa kanter, och inkluderar all nödvändig hårdvara för montering på M-LOK ytor.
Bearbetad aluminiumkropp med syntetisk, dämpande tändhatt som tål upprepad cykling.
Formad som laddade patroner för korrekt laddning och matning, vilket förbättrar skyttefärdigheter och vapenhantering.
Tävlingsskyttar och jägare kan öva på att ladda om och trycka avtryckaren för att förbättra sin skicklighet.
M-LOK QD Sling Mount erbjuder en främre fästpunkt för Magpul MS4 Sling och andra tryckknapp QD-selar.
Tillverkad från Mil-Spec anodiserad aluminium, passar den perfekt för handskydd och främre grepp kompatibla med M-LOK.
All nödvändig M-LOK-hårdvara för installation medföljer, och inga modifikationer av handskaftet krävs.