HORNADY
LOCK RINGS

090255440003 749000313

These steel die lock rings from Hornady clamp around the entire circumference of the die body. The lock screw squeezes the lock ring around the die with constant pressure across the threads - no jam screws. These rings have a flat on each side for wrench use. Sure-Lock Rings fit all standard 7/8""-14 reloading dies.

Mer...

Dessa ståldielåsningsringar från Hornady klämmer runt hela omkretsen av die-kroppen. Låsskruven pressar låsningsringen runt dien med konstant tryck över gängorna - inga klämskruvar. Dessa ringar har en platt sida på varje sida för användning med skiftnyckel. Sure-Lock Rings passar alla standard 7/8""-14 omladdningsdier.

Mer...

Kundernas betyg påHORNADY LOCK RINGS

Antal betyg: 5
Från brownells.com: 5
Medelbetyg: 4,2

excelent (2011-07-28)

this is an excelent replacement rign for any die set. you dont have to worry about stripping out the brass set screw like on other models and it squeezes the ring on the die instead of the screw contacting the threads of the die. because it isnt touching the threads so the set screw is made of steel and it will last you forever.

Great Ring (2012-05-04)

A good ring because you can lock it and also crank it down with wrench rather than having to mess with a channel-lock.

Works with Co-Ax press? (2013-03-15)

As stated in many places "works with Forster Co-ax press" NOT!
Might be to a design change, but very sloppy fit in this press. Constant misalignment on smaller cases. Case mouth hits decapping pin assembly 90% of the time. Bought 10 of these with the press, my mistake.

All die makers should use this design (2014-08-10)

I have Hornady, RCBS, Forster, Redding and Lee dies on my bench. I have found over time that I prefer the Hornady locking ring design. The ring is easily tightened with the included hex key. This design tensions the entire bearing surface of the ring, rather than a single point-of-contact set-screw.

When I buy a new non-Hornady die, the first thing I do is replace the locking ring with one of these.

Hornady Die lock rings (2017-07-25)

Nothing bothers me more than poorly designed die lock rings. My past history of 45 years of reloading began with the old RCBS lead pellet/setscrew system that impinged on the 7/8-14 threads of the die making it very difficult to adjust or remove off the die. Advancements then used brass setscrews then angled split ring design at a tangent to the threads which adjusted themselves closed against the threads,a much improved version.These Hornady lock rings allow their propriatory red handled wrench to properly secure this split ring tightly against the press body. Other manufacturers use their wrenches but still use the old setscrew that crushes against the die threads. I recommend these lock rings over any other type to include "O" ring spongy attachments.

Läs 5 fler betyg på brownells.com

0 0 1 SEK

Produktnr: 749000313
HORNADY LOCK RINGS
Tillverkarens produktnummer: 044000 090255440003 Dessa ståldielåsningsringar från Hornady klämmer runt hela omkretsen av die-kroppen. Låsskruven pressar låsningsringen runt dien med konstant tryck över gängorna - inga klämskruvar. Dessa ringar har en platt sida på varje sida för användning med skiftnyckel. Sure-Lock Rings passar alla standard 7/8""-14 omladdningsdier.

Meddela om tillgänglighet

Ej tillgänglig.

Funktioner: Stil: Die Lock Rings/Wrenches

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Top takeaways

Dessa Hornady ståldielåsningsringar klämmer runt hela omkretsen av die-kroppen för jämnt tryck.
Låsskruven pressar ringen med konstant tryck över gängorna, utan att använda klämskruvar.
Sure-Lock Rings har platta sidor för användning med skiftnyckel och passar alla standard 7/8"-14 omladdningsdier.

Produktinformation

Stil: Die Lock Rings/Wrenches Leveransvikt: 0,023kg Leveranshöjd: 15mm Leveransbredd: 43mm Leveranslängd: 76mm UPC : 090255440003