Över 300 000 kunder - vi sĂ€ger tack!

40 000+ produkter inom jakt och skytte

697566711152 430103596
BIS, G43X/48 (Backup Iron Sight, G43X/G48) is a collaboration between Ameriglo and FCD. Specifically made for Glock G43X and G48, these sights are based on the superb Ameriglo GL-527 with a front sight height of 0.450", and a rear sight height of 0.554", this sight sets provide lower 1/3 co-witness with the Trijicon RMRcc when used with the OPF-G43X/43, RMRcc on G43X and G48. BIS, G43X/48 consists of the following: Front sight, available with either green Tritium and white outline (no serrations), or serrated front sight, no tritium or white outline. Rear sight, serrated. BIS, G43X/48 is slightly different from GL-527 on which it's based. These FCD particular changes are: Tritium option for the front sight. Front sight back strap angle is steeper (25 degrees on the serrated, non-tritium front sight, 20 degrees on non-serrated, tritium front sight) to mitigate snagging when the pistol is drawn from and out of the holster where it's likely to encounter clothing, and the front sight's top corners are softened. Rear sight is horizontally serrated. Designed and made in the USA. Special thanks to the professionals at Ameriglo https://ameriglo.com/ that made this project possible, Forward Controls Design are grateful for their willingness to work with a small outfit for their shared customers / users. G43X/49 with RMRcc is approved by many agencies, most of which require red dot pistols be equipped with metallic, co-witnessing backup sights for both on and off duty use. BIS, G43X/48 was created with them in mind. NOTE: If you don't have a sight pusher or the equipment to install rear sights, please bring it to a qualified and competent gunsmith to perform the installation. It's not uncommon to have to fit the rear sight to the dovetail, a competent gunsmith should be well familiar with the reason and method. Forward Controls Design have seen more than enough expensive muzzle devices ruined by "gunsmiths" that used a screw driver to install them instead of a torque wrench, and hand tightened optics plate screws when a torque value is clearly noted in multiple places. Rather than being loose (easy to install), Forward Controls Design prefer the sights be tight, so it won't be knocked off zero easily. Tolerances of the dovetail and sights also come into play, which results in some being easier, while others are harder to install. A qualified gunsmith can deal with these easily.  
1749 1749 1 SEK
Produktnr: 430103596
FORWARD CONTROLS DESIGN GLOCK G43X/G48 BACKUP IRON SIGHT WITH TRITIUM
Tillverkarens produktnummer: BIS, 43X/48, WI 697566711152 BIS, G43X/48 (Backup Iron Sight, G43X/G48) Àr ett samarbete mellan Ameriglo och FCD. Speciellt framtagen för Glock G43X och G48, baseras dessa sikten pÄ det utmÀrkta Ameriglo GL-527 med en kornhöjd pÄ 0.450\", och ett bakre sikte pÄ 0.554\", detta sikteset ger lower 1/3 co-witness med Trijicon RMRcc nÀr det anvÀnds med OPF-G43X/43, RMRcc pÄ G43X och G48. BIS, G43X/48 bestÄr av följande: Korn, tillgÀngligt antingen med grönt Tritium och vit kontur (inga rÀfflor), eller rÀfflat korn, inget tritium eller vit kontur. Bakre sikte, rÀfflat. BIS, G43X/48 skiljer sig nÄgot frÄn GL-527 som det Àr baserat pÄ. Dessa specifika FCD-Àndringar inkluderar: Tritiumalternativ för kornet. Kornets baksidesvinkel Àr brantare (25 grader pÄ det rÀfflade, icke-tritium kornet, 20 grader pÄ det icke-rÀfflade, tritium kornet) för att minska risken för fasthakning nÀr pistolen dras frÄn och tillbaka i hölstret dÀr den sannolikt kommer i kontakt med klÀder, och kornets övre hörn Àr mjukgjorda. Bakre sikte Àr horisontellt rÀfflat. Designad och tillverkad i USA. Ett speciellt tack till proffsen pÄ Ameriglo https://ameriglo.com/ som gjorde detta projekt möjligt, Forward Controls Design Àr tacksamma för deras vilja att arbeta med ett mindre företag för deras gemensamma kunder/anvÀndare. G43X/49 med RMRcc Àr godkÀnd av mÄnga myndigheter, de flesta av dem krÀver att pistoler med rödpunktsikte Àr utrustade med metalliska, co-witnessing backup sikten för bÄde tjÀnst och privat bruk. BIS, G43X/48 skapades med dem i Ätanke. NOTERA: Om du inte har en siktflyttare eller utrustningen för att installera bakre sikten, vÀnligen ta med den till en kvalificerad och kompetent vapensmed för installation. Det Àr inte ovanligt att behöva passa in det bakre siktet i skÄran, en kompetent vapensmed bör vara vÀl bekant med anledningen och metoden. Forward Controls Design har sett alltför mÄnga dyra mynningsanordningar förstörda av \"vapensmeder\" som anvÀnt en skruvmejsel för att installera dem istÀllet för en momentnyckel, och handÄtdragna optikplatteskruvar nÀr ett momentvÀrde tydligt anges pÄ flera stÀllen. Hellre Àn att vara lösa (lÀtt att installera), föredrar Forward Controls Design att siktet Àr tajt, sÄ att det inte enkelt kan komma ur sitt nollÀge. Toleranser för skÄran och siktena spelar ocksÄ in, vilket resulterar i att vissa Àr lÀttare, medan andra Àr svÄrare att installera. En kvalificerad vapensmed kan enkelt hantera dessa.
1749 SEK 4 1 749,00 kr *
Leveranstid ca. 14-21 dagar.
4 st. i centrallagret.
Funktioner: Make: Glock Modell: 48, 43X SiktesfÀrg: Grön Stil: Tritium

Top takeaways

  1. BIS, G43X/48 Àr ett samarbete mellan Ameriglo och Forward Controls Design, speciellt framtaget för Glock G43X och G48.
  2. Kornet finns med grönt Tritium och vit kontur eller som rÀfflat utan Tritium, medan det bakre siktet Àr horisontellt rÀfflat.
  3. Designad och tillverkad i USA, erbjuder BIS lower 1/3 co-witness med Trijicon RMRcc och Àr godkÀnd av mÄnga myndigheter.

Produktinformation

Make: Glock Modell: 43X,48 SiktesfÀrg: Grön Stil: Tritium Leveransvikt: 0,363kg Leveranshöjd: 5mm Leveransbredd: 152mm LeveranslÀngd: 102mm UPC : 697566711152

Produkt detaljer

Tillverkas i USA

Ansvarig ekonomisk aktör enligt EU-förordningen

Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se





Uppgradera din Glock G43X/G48 med vĂ„rt Tritium Backup Iron Sight! 🌟 Perfekt co-witness med RMRcc för sĂ€ker skytte.

BIS, G43X/48 (Backup Iron Sight, G43X/G48) is a collaboration between Ameriglo and FCD. Specifically made for Glock G43X and G48, these sights are based on the superb Ameriglo GL-527 with a front sight height of 0.450", and a rear sight height of 0.554", this sight sets provide lower 1/3 co-witness with the Trijicon RMRcc when used with the OPF-G43X/43, RMRcc on G43X and G48. BIS, G43X/48 consists of the following: Front sight, available with either green Tritium and white outline (no serrations), or serrated front sight, no tritium or white outline. Rear sight, serrated. BIS, G43X/48 is slightly different from GL-527 on which it's based. These FCD particular changes are: Tritium option for the front sight. Front sight back strap angle is steeper (25 degrees on the serrated, non-tritium front sight, 20 degrees on non-serrated, tritium front sight) to mitigate snagging when the pistol is drawn from and out of the holster where it's likely to encounter clothing, and the front sight's top corners are softened. Rear sight is horizontally serrated. Designed and made in the USA. Special thanks to the professionals at Ameriglo https://ameriglo.com/ that made this project possible, Forward Controls Design are grateful for their willingness to work with a small outfit for their shared customers / users. G43X/49 with RMRcc is approved by many agencies, most of which require red dot pistols be equipped with metallic, co-witnessing backup sights for both on and off duty use. BIS, G43X/48 was created with them in mind. NOTE: If you don't have a sight pusher or the equipment to install rear sights, please bring it to a qualified and competent gunsmith to perform the installation. It's not uncommon to have to fit the rear sight to the dovetail, a competent gunsmith should be well familiar with the reason and method. Forward Controls Design have seen more than enough expensive muzzle devices ruined by "gunsmiths" that used a screw driver to install them instead of a torque wrench, and hand tightened optics plate screws when a torque value is clearly noted in multiple places. Rather than being loose (easy to install), Forward Controls Design prefer the sights be tight, so it won't be knocked off zero easily. Tolerances of the dovetail and sights also come into play, which results in some being easier, while others are harder to install. A qualified gunsmith can deal with these easily.  
Tillbaka till toppen