Traditional-length Rifle Buttstocks feature an easy-to-open storage compartment for emergency field tools, parts, or a Brownells AR-15 Buttstock Cleaning Kit. Fits both A1 and A2.
SPECS: Rifle Buttstock - 9-3⁄8" (23.8cm) long, 5” (12.7cm) high at tallest point, 2-1⁄8" (5.4cm) high at shortest point, 1-5⁄8" (4.1cm) wide.
Mer...
Mil-Spec Kvalitet, Hållbarhet & Utseende
Traditionella gevärskolvar i fullängd med ett lättöppnat förvaringsfack för nödverktyg, delar eller ett Brownells AR-15 Buttstock Cleaning Kit. Passar både A1 och A2.
SPECS: Gevärs-kolv - 9-3⁄8" (23.8cm) lång, 5” (12.7cm) hög vid högsta punkten, 2-1⁄8" (5.4cm) hög vid lägsta punkten, 1-5⁄8" (4.1cm) bred.
Antal betyg: 8
Från brownells.com: 8
Medelbetyg: 2,3
warning(2009-06-24)
This is a very cheaply made stock.The buttstock screw goes all the way through the butt pad and then all you have to do is pull back on the stock and it comes off completly.The only way to avoid this issue is not screw it in enough to tighten the buttstock.This stock is pure junk and I would'nt even want my enemies to use it
Decent stock for the money(2010-12-12)
This is a decent stock. It works well for what it is intended. The A1 style stock has been passed by with many of the newer wonder stocks. Remember that when replacing an A2 stock with this you will need a different screw for the stock, as A2s are longer due to the receiver extension spacer. The finish on the stock is a little rougher than it should be with some flashing showing. Other than that it is good to go. I also like to replace the butt-plate with an A2. That is just a matter of personal preference. I plan to buy another.
Poor quality stock(2011-07-01)
This is a very cheaply made stock. The trap door hinge is simply the same rubber piece used for the door. The attachment system is poor and the stock can be easily pulled off the buffer tube when you don't want it to come off! ( see other review ). The sling attachment is made of "square" material instead of round, rod type material. It should cut through a sling in a matter of hours.
Absolutely hot garbage(2015-10-18)
I needed to do a build with an A1 stock length and a weighted stock, so I tried this. Big mistake. Plastic stock that I wouldn't put on a kid's airsoft. Buttplate was flimsy and didn't fit the stock, the sling loop went from side to side in a 270° arc, eventually working loose, and would have cut any sling you put through it. The trapdoor seemed to be made out of the same sort of vinyl usually found in electrical tape, but less useful.
I tried to modify it by replacing the buttplate, and that was useless becase nothing on this thing mached any standard, milspec or commercial. The first buttplate slipped right off the end of the buffer tube screw, which was handy because the screw was stuck. Then the original lower screw crossthreaded in the sling loop.
I'm returning it to Brownells with a request that they never sell it again.
Yea wasted 50 bucks(2017-12-14)
Top screw went right thru the butt plate
Cavalry Manufacturing A1 butt stock.(2018-01-25)
If your looking for an A1 length butt stock that you can use and not worry about digging up or failing on you this is it. texture is not like an original, and the butt plate and trap door are a bit flimsy but can be replaced with Oem A1or A2 components.overall construction and materials are very strong.i would consider this stock for anyone who is going to use their rifle for hunting,target,or tactical shooting.if you or building a true A1 clone, i would suggest for you to purchase nos,refurbished military surplus. If you want something you can use everyday.you can't beat the deal on this butt stock.
One TSOB(2018-07-17)
Really nice copy of a a1 stock. Accepted My old butt plate and has a ton of space for stuff inside stock due to the lack of foam.
Really nice job guys.
Thanks
Rich
Buttpad ruins it(2018-09-22)
The stock itself is ok. It is the correct A1 length. The buttplate is a flimsy, rubbery piece of garbage that gets drilled through by the install screw. Would not recommend. Brownells should discontinue selling this product.
If you want an A1 length fixed stock for your rifle, get a Brownells retro A1 stock instead.
Produktnr: 100000939 CAVALRY MANUFACTURING. AR-15 STOCK FIXED RIFLE LENGTH BLK Tillverkarens produktnummer: NONE Traditionella gevärskolvar i fullängd med ett lättöppnat förvaringsfack för nödverktyg, delar eller ett Brownells AR-15 Buttstock Cleaning Kit. Passar både A1 och A2.
1099SEK61 099,00 kr
*
Levernastid ca. 14-21 dagar. 6 st. i centrallagret.
Tillverkas i USA
USA: s exportklassificering: 0A501.y.1
Destination Control Statement: Dessa poster styrs av USA: s regering och godkänns endast för export till det land där den slutliga destinationen används av den slutliga mottagaren eller slutanvändaren som identifierats här. De får inte vidareförsäljas, överföras eller på annat sätt kasseras till något annat land eller någon annan än den godkända slutliga mottagaren eller slutanvändaren, antingen i sin ursprungliga form eller efter att ha monterats i andra föremål utan att först få godkännande från den amerikanska regeringen eller som annars är tillåten enligt amerikansk lag och förordningar.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Upptäck AR-15 fixed rifle length kolv från CAVALRY MANUFACTURING. 🛠️ Perfekt för A1 och A2, med praktiskt förvaringsfack.
Traditional-length Rifle Buttstocks feature an easy-to-open storage compartment for emergency field tools, parts, or a Brownells AR-15 Buttstock Cleaning Kit. Fits both A1 and A2.
SPECS: Rifle Buttstock - 9-3⁄8" (23.8cm) long, 5” (12.7cm) high at tallest point, 2-1⁄8" (5.4cm) high at shortest point, 1-5⁄8" (4.1cm) wide.
Mer...
Mil-Spec Kvalitet, Hållbarhet & Utseende
Traditionella gevärskolvar i fullängd med ett lättöppnat förvaringsfack för nödverktyg, delar eller ett Brownells AR-15 Buttstock Cleaning Kit. Passar både A1 och A2.
SPECS: Gevärs-kolv - 9-3⁄8" (23.8cm) lång, 5” (12.7cm) hög vid högsta punkten, 2-1⁄8" (5.4cm) hög vid lägsta punkten, 1-5⁄8" (4.1cm) bred.
Antal betyg: 8
Från brownells.com: 8
Medelbetyg: 2,3
warning(2009-06-24)
This is a very cheaply made stock.The buttstock screw goes all the way through the butt pad and then all you have to do is pull back on the stock and it comes off completly.The only way to avoid this issue is not screw it in enough to tighten the buttstock.This stock is pure junk and I would'nt even want my enemies to use it
Decent stock for the money(2010-12-12)
This is a decent stock. It works well for what it is intended. The A1 style stock has been passed by with many of the newer wonder stocks. Remember that when replacing an A2 stock with this you will need a different screw for the stock, as A2s are longer due to the receiver extension spacer. The finish on the stock is a little rougher than it should be with some flashing showing. Other than that it is good to go. I also like to replace the butt-plate with an A2. That is just a matter of personal preference. I plan to buy another.
Poor quality stock(2011-07-01)
This is a very cheaply made stock. The trap door hinge is simply the same rubber piece used for the door. The attachment system is poor and the stock can be easily pulled off the buffer tube when you don't want it to come off! ( see other review ). The sling attachment is made of "square" material instead of round, rod type material. It should cut through a sling in a matter of hours.
Absolutely hot garbage(2015-10-18)
I needed to do a build with an A1 stock length and a weighted stock, so I tried this. Big mistake. Plastic stock that I wouldn't put on a kid's airsoft. Buttplate was flimsy and didn't fit the stock, the sling loop went from side to side in a 270° arc, eventually working loose, and would have cut any sling you put through it. The trapdoor seemed to be made out of the same sort of vinyl usually found in electrical tape, but less useful.
I tried to modify it by replacing the buttplate, and that was useless becase nothing on this thing mached any standard, milspec or commercial. The first buttplate slipped right off the end of the buffer tube screw, which was handy because the screw was stuck. Then the original lower screw crossthreaded in the sling loop.
I'm returning it to Brownells with a request that they never sell it again.
Yea wasted 50 bucks(2017-12-14)
Top screw went right thru the butt plate
Cavalry Manufacturing A1 butt stock.(2018-01-25)
If your looking for an A1 length butt stock that you can use and not worry about digging up or failing on you this is it. texture is not like an original, and the butt plate and trap door are a bit flimsy but can be replaced with Oem A1or A2 components.overall construction and materials are very strong.i would consider this stock for anyone who is going to use their rifle for hunting,target,or tactical shooting.if you or building a true A1 clone, i would suggest for you to purchase nos,refurbished military surplus. If you want something you can use everyday.you can't beat the deal on this butt stock.
One TSOB(2018-07-17)
Really nice copy of a a1 stock. Accepted My old butt plate and has a ton of space for stuff inside stock due to the lack of foam.
Really nice job guys.
Thanks
Rich
Buttpad ruins it(2018-09-22)
The stock itself is ok. It is the correct A1 length. The buttplate is a flimsy, rubbery piece of garbage that gets drilled through by the install screw. Would not recommend. Brownells should discontinue selling this product.
If you want an A1 length fixed stock for your rifle, get a Brownells retro A1 stock instead.