Varukorgen är tom.

Varukorg

Hjälp och kontakt

Fri frakt på beställningar över 2.999 kr

100 dagars returrätt

Nyhetsbrev

REA

Över 300 000 kunder - vi säger tack!

4,93/5 "Mycket bra" (1400+ recensioner)

40 000+ produkter inom jakt och skytte

CLARK CUSTOM
1911 BARREL BUSHING

181001145

Improve Accuracy, Eliminate Excess Play

Standard fits most barrels with only minor polishing/fitting. Fully machined. Favorite bushing of experienced pistolsmiths. Requires gunsmith fitting.

SPECS: .875" (22.22mm) long, .714" (18.13mm) O.D. Std, .575" (14.55mm) I.D.

Mer...

Förbättra precisionen, eliminera onödigt spel

Standard passar de flesta pipor med endast mindre polering/anpassning. Helt bearbetad. Favoritbussning bland erfarna vapensmeder. Kräver montering av vapensmed.

SPECS: .875" (22,22mm) lång, .714" (18,13mm) Y.D. Std, .575" (14,55mm) I.D.

Mer...

Kundernas betyg påCLARK CUSTOM STANDARD BARREL BUSHING

Antal betyg: 2
Från brownells.com: 2
Medelbetyg: 4

VERY Oversized, tricky to fit. (2010-07-01)

I purchased this bushing along with a Clark Custom 6" .45 ACP non-ramped barrel, to fit to a Caspian XR slide. I have used Clark barrels before with much success, so figured I'd give their bushing a shot.

The ID of the bushing where the barrel slides through has a LOT of material. As the description says, it is better for undersized/G.I. barrels, not a full-sized match barrel. It took a good while with an adjustable hand reamer to remove enough material to fit it to the barrel properly to a light drag fit.

Unlike most other bushings which are completely round on the skirt, this has 3 flanges that contact the ID of the slide where the barrel rides. I figured this would be easy enough, using the Brownells bushing mandrel to turn it down on a lathe. I cut the flanges until it would slide into the opening, yet I was still getting drag marks on the leading flange as I tried to twist the bushing into place with a bushing wrench.

Turns out the flanges are also oversized for the tunnel in which the lug rides, and on the forward edge of the lug as well as the outer surface of the bushing that contacts the slide. In all there are about 8 points of contact (including the ID where the barrel rides) to fit on this bushing. Very time consuming.

I have fit other manufacturers' oversized bushings, which tool much longer and served to build very accurate pistols. I'd stay away from this one unless you've got tons of experience or lots of spare time on your hands.

Excellent product (2011-11-05)

I use these bushings for both bullseye and game guns. In my opinion, its the best bushing you can buy. A lathe makes short work in the fitting department, and you don't have to use your barrel as a slide hammer.

Läs 2 fler betyg på brownells.com

419 419 1 SEK

Produktnr: 181001145
CLARK CUSTOM STANDARD BARREL BUSHING
Tillverkarens produktnummer: CLK170575 Standard passar de flesta pipor med endast mindre polering/anpassning. Helt bearbetad. Favoritbussning bland erfarna vapensmeder. Kräver montering av vapensmed.

419 SEK 0 419,00 kr *

Restorder. Skickas när den finns i lager. Leveranstid ca 4-12 veckor från centrallagret.

Funktioner: Finish: Blånerad Make: 1911 Modell: Government Stil: Drop-In

Lägg till i inköpslista

Fråga om produkt

Information

Lägg till i inköpslista

Fråga om produkt

Produktinformation

Finish: Blånerad Make: 1911 Modell: Government Stil: Drop-In Leveransvikt: 0,018kg Leveransbredd: 83mm Leveranslängd: 146mm

Produkt detaljer

Tillverkas i USA

Ansvarig ekonomisk aktör enligt EU-förordningen

Brownells Sverige AB
Box 99
793 22 Leksand
Sverige
info@brownells.se

Upptäck vår 1911 BARREL BUSHING från CLARK CUSTOM! 🔧 Perfekt för erfarna vapensmeder, kräver minimal anpassning för bästa passform.

Improve Accuracy, Eliminate Excess Play

Standard fits most barrels with only minor polishing/fitting. Fully machined. Favorite bushing of experienced pistolsmiths. Requires gunsmith fitting.

SPECS: .875" (22.22mm) long, .714" (18.13mm) O.D. Std, .575" (14.55mm) I.D.

Mer...

Förbättra precisionen, eliminera onödigt spel

Standard passar de flesta pipor med endast mindre polering/anpassning. Helt bearbetad. Favoritbussning bland erfarna vapensmeder. Kräver montering av vapensmed.

SPECS: .875" (22,22mm) lång, .714" (18,13mm) Y.D. Std, .575" (14,55mm) I.D.

Mer...